HALL sensor

[mikes02ls1]

Does anyone know where the three wires from the HALL sensor PIN into? Like PIN location? 92 944 with a 87 760 dizzy... The three wires i have are a ground at PIN 8-11,Blue wire with a resistor at PIN 24ish, and Yellow wire at PIN 27ish... it looks like another wire was attached to the resistor but where did it attached to? This is all that is holding me from starting her.

[mikes02ls1]

http://img518.imageshack.us/img518/2713/strom028hg3.th.jpg (http://img518.imageshack.us/my.php?image=strom028hg3.jpg)

http://img291.imageshack.us/img291/2944/strom034hn2.th.jpg (http://img291.imageshack.us/my.php?image=strom034hn2.jpg)http://img291.imageshack.us/images/thpix.gif (http://g.imageshack.us/thpix.php)

http://img403.imageshack.us/img403/7627/strom032sp6.th.jpg (http://img403.imageshack.us/my.php?image=strom032sp6.jpg)http://img403.imageshack.us/images/thpix.gif (http://g.imageshack.us/thpix.php)
Kenny those are the three wires. With the resistor on the blue was there another wire attached to it, and what was it?

[500dollar744ti]

in my diagram for lh2.2-->MS it should show where they go...

in the diagram, you have to follow it from the ezk box back to the lh box and then to the db37 though.

http://forums.turbobricks.com/showthread.php?t=121163

[linuxman51]

his is lh 2.4, with a head mounted distributor.

[linuxman51]

and the first picture is unintelligible, the second one you need to flip the connector over.

[mikes02ls1]

and the first picture is unintelligible, the second one you need to flip the connector over.Click on the picture. You can see the resistor on the blue wire, then there is the yellow wire, then the ground. Its the three that are cut. sorry.

[linuxman51]

I can't tell from that side of the picture. If there's a resistor inline on the blue wire and its attached to pin28/red then that is +12v and yellow is signal to the hall. black is ground. whats the cut purple wire in the harness?

[mikes02ls1]

I can't tell from that side of the picture. If there's a resistor inline on the blue wire and its attached to pin28/red then that is +12v and yellow is signal to the hall. black is ground. whats the cut purple wire in the harness?
Yellow wire is attached to the red wire. Blues has the resistor, cut purple wire I'm not sure I thought it something you did..

[linuxman51]

something is missing. what pin does the blue wire attach to at the ms connector? (what color is next to it). purple should be 02, did the p.o. wire in a wideband at some point?

[mikes02ls1]

something is missing. what pin does the blue wire attach to at the ms connector? (what color is next to it). purple should be 02, did the p.o. wire in a wideband at some point?
No wideband from what Mike told me, Jerry at DIY said he didn't think the o2 was working.. I will go outside to triple check what PIN the blue wire is in on the MS connector. Blue is next to a light blue wire.

[mikes02ls1]

PIN 24 is the blue wire with the resistor. PIN 28 is the red wire with the yellow attached. PIN 25 is the light blue wire next to the darker blue wire. PIN 7-11 is the ground.

[linuxman51]

Did you cut pin 24? it should be attached to pin 28 with the resistor. the yellow wire coming off pin 28 is power for the hall, signal comes into the ms on pin 25. ground is of course ground.

[mikes02ls1]

Did you cut pin 24? it should be attached to pin 28 with the resistor. the yellow wire coming off pin 28 is power for the hall, signal comes into the ms on pin 25. ground is of course ground.Yeah those three wires got burnt so I left some wire so I can resolder to the new harness. So the blue wire is attched to the yellow wire?

So where does the red wire on the HALL sensor go to o the MS connector?