home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.11 seconds.
Search: Posts Made By: ZVOLV
Forum: maintenance & nonperformance Yesterday, 08:14 PM
Replies: 6
Views: 94
Posted By ZVOLV
Dual mass flywheel failing....

Dual mass flywheel failing....
Forum: maintenance & nonperformance Yesterday, 07:23 PM
Replies: 48
Views: 440
Posted By ZVOLV
$1 test light connected to the starter solenoid...

$1 test light connected to the starter solenoid wire. Crank key. Light go on? Takes 30 seconds to track down if your starter is getting a signal or not.
Forum: maintenance & nonperformance Yesterday, 07:04 PM
Replies: 13
Views: 487
Posted By ZVOLV
Do diag!!! Get a test lamp and go for the easy...

Do diag!!! Get a test lamp and go for the easy access stuff first. Learn to read a wiring diagram.

Yes, if it runs on alternate fuel, I would go towards fuel system diag.

Essential tools are...
Forum: maintenance & nonperformance Yesterday, 06:16 PM
Replies: 6
Views: 157
Posted By ZVOLV
I bet degraded wiring under the intake. Injector...

I bet degraded wiring under the intake. Injector control circuit shorted to the ground wiring.
Forum: maintenance & nonperformance Yesterday, 12:56 AM
Replies: 48
Views: 440
Posted By ZVOLV
Convert to megaswuirt.

Convert to megaswuirt.
Forum: maintenance & nonperformance 09-17-2018, 08:17 PM
Replies: 48
Views: 440
Posted By ZVOLV
Won't turn over? Put a rip cord on the crank...

Won't turn over? Put a rip cord on the crank pulley.
Forum: maintenance & nonperformance 09-17-2018, 04:55 PM
Replies: 84
Views: 2,322
Posted By ZVOLV
I fail to see how twisting a crank sensor in the...

I fail to see how twisting a crank sensor in the bore would do anything. Sounds like the wiring may be bad.

Nice find.
Forum: maintenance & nonperformance 09-17-2018, 03:23 PM
Replies: 12
Views: 266
Posted By ZVOLV
Boiling water may work. Or a heat gun. Probably...

Boiling water may work. Or a heat gun. Probably don't wanna use a torch...

Lots of threads on repairing kjet fuel lines-same.
Forum: maintenance & nonperformance 09-17-2018, 02:32 PM
Replies: 84
Views: 2,322
Posted By ZVOLV
A test lamp to the coil control circuit (ground)...

A test lamp to the coil control circuit (ground) should illuminate the bulb with key on, and blink while you crank. Build one with a spare bulb and solder some wire onto it. You should see a steady...
Forum: maintenance & nonperformance 09-17-2018, 02:28 PM
Replies: 10
Views: 490
Posted By ZVOLV
Have you tested the wiring to the cam sensor yet?...

Have you tested the wiring to the cam sensor yet? I imagine it's a a 5v reference, signal, and a ground. So I would expect to see 5v on one wire, a scope would show you a solid waveform on the signal...
Forum: maintenance & nonperformance 09-17-2018, 02:25 PM
Replies: 84
Views: 2,322
Posted By ZVOLV
You can check resistance of a crank sensor, but...

You can check resistance of a crank sensor, but it prob won't tell you much. You know it's not totally open.

I would really analyze and inspect for a steady primary and secondary ignition pulse...
Forum: maintenance & nonperformance 09-17-2018, 01:43 PM
Replies: 84
Views: 2,322
Posted By ZVOLV
First start by pulling the flexplate shield and...

First start by pulling the flexplate shield and do a visual inspection.

You could also do basic stuff like use a test light to the coil negative wire and see if it blinks steadily while cranking....
Forum: maintenance & nonperformance 09-17-2018, 12:52 PM
Replies: 84
Views: 2,322
Posted By ZVOLV
Yep. I use a Pico, but I also have a $80 Hantek. ...

Yep. I use a Pico, but I also have a $80 Hantek.

Blue is a crank sesnor waveform at idle. If your tone ring were bent or incorrect gap, you would see an irregular waveform.

...
Forum: maintenance & nonperformance 09-17-2018, 11:43 AM
Replies: 84
Views: 2,322
Posted By ZVOLV
Labscope.

Labscope.
Forum: maintenance & nonperformance 09-16-2018, 04:06 PM
Replies: 8
Views: 216
Posted By ZVOLV
1983 740?

1983 740?
Forum: performance & modifications 09-16-2018, 01:54 PM
Replies: 55
Views: 1,330
Posted By ZVOLV
That's great he offers that stuff. That's how I...

That's great he offers that stuff. That's how I professionally repair bad circuits- NEW terminal ends and new wiring.
Forum: performance & modifications 09-16-2018, 01:43 PM
Replies: 55
Views: 1,330
Posted By ZVOLV
I took the mechanical fan off my 1991 740 Turbo...

I took the mechanical fan off my 1991 740 Turbo and never got around to putting another on back on. I'm running off just the pusher fan on the condenser right now. Wheeeeee!
Forum: maintenance & nonperformance 09-15-2018, 03:04 PM
Replies: 19
Views: 519
Posted By ZVOLV
I'm giving up on telling tbrickers how to use a...

I'm giving up on telling tbrickers how to use a meter.
Forum: maintenance & nonperformance 09-15-2018, 03:03 PM
Replies: 9
Views: 389
Posted By ZVOLV
I broke a $500 windshield with my elbow using...

I broke a $500 windshield with my elbow using brute man-strength with that method. I recommend caution.
Forum: maintenance & nonperformance 09-14-2018, 07:42 PM
Replies: 9
Views: 389
Posted By ZVOLV
Open end wrench under it and hammer. (Thanks...

Open end wrench under it and hammer. (Thanks Philski)
Forum: maintenance & nonperformance 09-14-2018, 07:41 PM
Replies: 10
Views: 490
Posted By ZVOLV
Cam timing off may throw a cam sensor code.

Cam timing off may throw a cam sensor code.
Forum: performance & modifications 09-14-2018, 12:07 PM
Replies: 10
Views: 586
Posted By ZVOLV
^^^sounds like your ignition switch isn't wired...

^^^sounds like your ignition switch isn't wired correctly for 2.4.
Forum: maintenance & nonperformance 09-13-2018, 07:43 PM
Replies: 19
Views: 519
Posted By ZVOLV
That's what I was wondering too. Try another...

That's what I was wondering too. Try another known good one.

Codes?

What's the o2 sensor voltage?
Forum: maintenance & nonperformance 09-13-2018, 02:31 PM
Replies: 42
Views: 817
Posted By ZVOLV
Water in floor!? Probably fuse holder fretting....

Water in floor!? Probably fuse holder fretting. Clean the fuses and holders gently. Wire brush is too coarse. Some people say every cloth is the way to go. Dielectric grease can't hurt either.
Forum: maintenance & nonperformance 09-12-2018, 08:57 PM
Replies: 13
Views: 487
Posted By ZVOLV
Oh yeah it may be 1.0LH. Anyways, alternate fuel...

Oh yeah it may be 1.0LH. Anyways, alternate fuel (spray) usually narrows it down to fuel system. I did, one time, see a Honda run on brake cleaner with a damaged crank sensor.

Disable the fuel...
Forum: maintenance & nonperformance 09-12-2018, 08:09 PM
Replies: 13
Views: 487
Posted By ZVOLV
You DISABLE the fuel system and then run it off...

You DISABLE the fuel system and then run it off the spray can into the throttle. I don't like pushing trucks with dead fuel pumps, for example, so one man is under the hood pulsing the spray and...
Forum: maintenance & nonperformance 09-12-2018, 08:05 PM
Replies: 5
Views: 276
Posted By ZVOLV
Only rookies front probe without the proper test...

Only rookies front probe without the proper test lead.

Needle probes work if you have to front probe, but you can still damage the terminal.

I made some front probing pins out of a spare...
Forum: maintenance & nonperformance 09-12-2018, 03:12 PM
Replies: 7
Views: 380
Posted By ZVOLV
Nice. Looks crooked...

Nice. Looks crooked...
Forum: maintenance & nonperformance 09-12-2018, 01:11 PM
Replies: 16
Views: 768
Posted By ZVOLV
So what you are trying to tell me is that you DO...

So what you are trying to tell me is that you DO have fuel injector pulse???

Good find. A test light would have revealed this. Or a noid light.


Wait a second.....240 doesn't have a radio blah...
Forum: maintenance & nonperformance 09-12-2018, 10:11 AM
Replies: 16
Views: 768
Posted By ZVOLV
Do you have power and ground to the computers?...

Do you have power and ground to the computers? Meter or lamp works. Check for codes???? This will also confirm if computers are alive.

Fuel injector pulse???
Forum: maintenance & nonperformance 09-12-2018, 10:10 AM
Replies: 19
Views: 519
Posted By ZVOLV
Follow my article. Does it stay running pulsing...

Follow my article. Does it stay running pulsing it on ether?
Forum: maintenance & nonperformance 09-11-2018, 11:24 PM
Replies: 13
Views: 487
Posted By ZVOLV
See if it stays running on pulses of spray!

See if it stays running on pulses of spray!
Forum: maintenance & nonperformance 09-11-2018, 04:04 PM
Replies: 3
Views: 267
Posted By ZVOLV
This. Pop the oil cap and crank and does cam spin?

This. Pop the oil cap and crank and does cam spin?
Forum: maintenance & nonperformance 09-11-2018, 04:04 PM
Replies: 19
Views: 519
Posted By ZVOLV
Click my sig

Click my sig
Forum: maintenance & nonperformance 09-10-2018, 01:44 PM
Replies: 42
Views: 817
Posted By ZVOLV
Moisture non starts on a 240 can be better...

Moisture non starts on a 240 can be better terminals, fuse at battery, fuses getting wet from windshield leaks or moisture, wet junction block at fender, grounds at intake manifold. On a 740 it's...
Forum: maintenance & nonperformance 09-10-2018, 10:18 AM
Replies: 8
Views: 443
Posted By ZVOLV
^^^ ...

^^^

http://forums.tbforums.com/picture.php?albumid=398&pictureid=3486
Forum: maintenance & nonperformance 09-09-2018, 06:03 PM
Replies: 16
Views: 768
Posted By ZVOLV
Do you have injector pulse?

Do you have injector pulse?
Forum: performance & modifications 09-04-2018, 02:16 PM
Replies: 28
Views: 1,421
Posted By ZVOLV
^^^unless you're drunk.

^^^unless you're drunk.
Forum: maintenance & nonperformance 08-31-2018, 06:28 PM
Replies: 10
Views: 435
Posted By ZVOLV
Do you still have your parts 240? Snip off ANY of...

Do you still have your parts 240? Snip off ANY of the terminals from your engine bay harness as a donor lead. You don't need the clip. Actually, you can probably pop it open easily and retain the...
Forum: maintenance & nonperformance 08-30-2018, 07:30 PM
Replies: 20
Views: 694
Posted By ZVOLV
Backfiring is lean or ignition timing.

Backfiring is lean or ignition timing.
Forum: maintenance & nonperformance 08-29-2018, 06:40 PM
Replies: 17
Views: 721
Posted By ZVOLV
So I pulled an alum diff cover off a 1989 740 GLE...

So I pulled an alum diff cover off a 1989 740 GLE 16v Saturday and found there was no G80 in there. To my surprise, I also found a one tooth sensor in the cover. Maybe this would be the solution to...
Forum: events 08-29-2018, 01:42 PM
Replies: 26
Views: 586
Posted By ZVOLV
Bring the 6 foot bong. Ice Cube is...

Bring the 6 foot bong.



Ice Cube is Sunday for $6. Gonna be there?
Forum: events 08-28-2018, 03:51 PM
Replies: 26
Views: 586
Posted By ZVOLV
BBQ? Saturday there's a $6 Slightly Stoopid...

BBQ?

Saturday there's a $6 Slightly Stoopid reggae show at the race track.

40% off weekend at junkards. Pretty bare nowadays. I can't even find a good 15G anymore.

Gotta get my 4.10 gears...
Forum: maintenance & nonperformance 08-28-2018, 03:36 PM
Replies: 5
Views: 297
Posted By ZVOLV
https://photos.smugmug.com/Cars/Volvo-17/i-HsqtcZN...

https://photos.smugmug.com/Cars/Volvo-17/i-HsqtcZN/0/741ba76a/M/47A24046-37DA-471E-8BBA-63D64D306E54-M.jpg

This is where much of the slop comes from. I recall a guy having success maybe installing...
Forum: maintenance & nonperformance 08-28-2018, 12:43 PM
Replies: 5
Views: 297
Posted By ZVOLV
The coupler at the shift rod at the trans is a...

The coupler at the shift rod at the trans is a source of most of the slop. You are gonna have to get creative to fix it.
Forum: events 08-25-2018, 05:43 PM
Replies: 26
Views: 586
Posted By ZVOLV
Im gonna try to get a 16T, 4.10 gears, and some...

Im gonna try to get a 16T, 4.10 gears, and some E85 in my stock 1991 740 Turbo and do the drag strip. Boost it as high as I can and if the B230FT survives. Im swapping the engine soon so might as...
Forum: maintenance & nonperformance 08-25-2018, 10:45 AM
Replies: 4
Views: 316
Posted By ZVOLV
My 1990 240 would toss this code sometimes in the...

My 1990 240 would toss this code sometimes in the mornings. It ended up being poor connections at the battery and the fuse by the battery.
Forum: maintenance & nonperformance 08-24-2018, 03:49 PM
Replies: 7
Views: 378
Posted By ZVOLV
Check the voltage output. Even then, I had a...

Check the voltage output. Even then, I had a Nissan Sentra once that was reading OK on the scan tool voltage (which can vary from a meter reading) and the car still stalled at idle. Research pointed...
Forum: maintenance & nonperformance 08-23-2018, 11:44 PM
Replies: 17
Views: 721
Posted By ZVOLV
Mine didn't work with the steel cover and chopped...

Mine didn't work with the steel cover and chopped up 48 window -to-12 window either...

I thought alum would be the answer but it didn't fix it either. Idk
Forum: events 08-22-2018, 06:07 PM
Replies: 26
Views: 586
Posted By ZVOLV
I can haul my AW72L there. $40. Need beer money.

I can haul my AW72L there. $40. Need beer money.
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 08:51 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.