home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.09 seconds.
Search: Posts Made By: ZVOLV
Forum: maintenance & nonperformance Today, 12:55 PM
Replies: 2
Views: 73
Posted By ZVOLV
A wiring diagram.

A wiring diagram.
Forum: maintenance & nonperformance 09-16-2019, 02:42 PM
Replies: 53
Views: 2,235
Posted By ZVOLV
Use an air hammer to get the nut off.

Use an air hammer to get the nut off.
Forum: maintenance & nonperformance 09-13-2019, 08:49 PM
Replies: 17
Views: 530
Posted By ZVOLV
2.5 cans is not a weight.

2.5 cans is not a weight.
Forum: maintenance & nonperformance 09-13-2019, 02:17 PM
Replies: 48
Views: 2,575
Posted By ZVOLV
I'd string a new circuit from the MAF to ECM with...

I'd string a new circuit from the MAF to ECM with new terminals. Then replace the ECM.
Forum: maintenance & nonperformance 09-12-2019, 07:48 PM
Replies: 17
Views: 530
Posted By ZVOLV
What was the total WEIGHT of refrigerant you...

What was the total WEIGHT of refrigerant you installed?

Did you flush all the old oil? 6 Oz may be close to total capacity.

Did you read the instructions with the new compressor on how to...
Forum: maintenance & nonperformance 09-12-2019, 07:06 PM
Replies: 5
Views: 426
Posted By ZVOLV
This.^^^

This.^^^
Forum: maintenance & nonperformance 09-12-2019, 02:36 PM
Replies: 17
Views: 530
Posted By ZVOLV
6 Oz of oil is a lot. Do you have a pusher...

6 Oz of oil is a lot.

Do you have a pusher fan?
Forum: maintenance & nonperformance 09-11-2019, 08:00 PM
Replies: 14
Views: 633
Posted By ZVOLV
Floor console wiring is common. Unplug it all and...

Floor console wiring is common. Unplug it all and try again.
Forum: maintenance & nonperformance 09-09-2019, 08:58 PM
Replies: 12
Views: 579
Posted By ZVOLV
Incandescent lamp between coil negative and...

Incandescent lamp between coil negative and ground. Blink?


LED lamp to powerstage "input" wire. Blink?
Forum: maintenance & nonperformance 09-09-2019, 08:46 PM
Replies: 3
Views: 319
Posted By ZVOLV
Ha. I saw it today. Sounds like he found one in...

Ha. I saw it today. Sounds like he found one in his wanted thread.
Forum: maintenance & nonperformance 09-08-2019, 06:35 PM
Replies: 12
Views: 579
Posted By ZVOLV
Do you have a test lamp?

Do you have a test lamp?
Forum: maintenance & nonperformance 09-06-2019, 02:57 AM
Replies: 25
Views: 952
Posted By ZVOLV
With a lift and a screw jack---- under an hour...

With a lift and a screw jack---- under an hour with good tools.

Bull****ting with tbrickers in a driveway with hand tools and a floor jack......maybe the day, depending on how much beer we drank.
Forum: maintenance & nonperformance 09-05-2019, 10:42 PM
Replies: 48
Views: 2,575
Posted By ZVOLV
That means the reading is out of the range of the...

That means the reading is out of the range of the setting you have it on.

Do you have a good MAF reading, backprobed at the ECU?
Forum: maintenance & nonperformance 09-05-2019, 04:52 PM
Replies: 27
Views: 1,692
Posted By ZVOLV
Test lamps are $3 at Harbor Freight. A meter is...

Test lamps are $3 at Harbor Freight. A meter is the wrong tool!!
Forum: maintenance & nonperformance 08-30-2019, 11:09 AM
Replies: 48
Views: 2,575
Posted By ZVOLV
Armed with the wiring diagram, how does one...

Armed with the wiring diagram, how does one diagnose the MAF circuit??
Forum: maintenance & nonperformance 08-29-2019, 02:41 AM
Replies: 16
Views: 794
Posted By ZVOLV
Use needle probes for backprobing. Only...

Use needle probes for backprobing.

Only front probe with the proper probe. I got some for $100. Or make test leads using pins from old components and solder on a wire.
Forum: maintenance & nonperformance 08-28-2019, 06:39 PM
Replies: 11
Views: 514
Posted By ZVOLV
^^^ yep. That kit. Except I always go thru the...

^^^ yep. That kit. Except I always go thru the passenger side just in case I damage something.


Where's that video from 500dollar740 where he slips a packing tie down onto the lock knob...

I...
Forum: maintenance & nonperformance 08-28-2019, 04:23 PM
Replies: 16
Views: 794
Posted By ZVOLV
You probably have an air leak. I use a smoke...

You probably have an air leak. I use a smoke machine.
Forum: maintenance & nonperformance 08-28-2019, 01:21 PM
Replies: 11
Views: 514
Posted By ZVOLV
A wedge, inflatable bag, and a rod. I have the...

A wedge, inflatable bag, and a rod. I have the kit at work.
Forum: maintenance & nonperformance 08-27-2019, 08:48 PM
Replies: 8
Views: 624
Posted By ZVOLV
It does sound like a bad ground and current is...

It does sound like a bad ground and current is back feeding thru the chime circuit.
Forum: maintenance & nonperformance 08-27-2019, 08:45 PM
Replies: 16
Views: 794
Posted By ZVOLV
O2 voltage should oscillate.

O2 voltage should oscillate.
Forum: maintenance & nonperformance 08-27-2019, 06:06 PM
Replies: 48
Views: 2,575
Posted By ZVOLV
You gotta check terminal tension at the MAF and...

You gotta check terminal tension at the MAF and ECU. Make a tool.

Check continuity between the ECU and MAF circuit/s.

Do a loaded voltage drop on the ECU ground circuit.


Have you...
Forum: maintenance & nonperformance 08-27-2019, 12:43 PM
Replies: 24
Views: 3,256
Posted By ZVOLV
Pico NVH

Pico NVH
Forum: maintenance & nonperformance 08-24-2019, 08:37 PM
Replies: 48
Views: 2,575
Posted By ZVOLV
Did you do the tests I mentioned?

Did you do the tests I mentioned?
Forum: performance & modifications 08-22-2019, 12:57 PM
Replies: 5
Views: 586
Posted By ZVOLV
Use the marks on the new belt.

Use the marks on the new belt.
Forum: maintenance & nonperformance 08-21-2019, 07:48 PM
Replies: 17
Views: 887
Posted By ZVOLV
29,000,000 miles is the problem.

29,000,000 miles is the problem.
Forum: maintenance & nonperformance 08-21-2019, 06:36 PM
Replies: 29
Views: 1,284
Posted By ZVOLV
Nice! I was wondering about this yesterday, but...

Nice! I was wondering about this yesterday, but hasn't posted about it.

You had: spark, injector pulse, runs on brake cleaner= diag the fuel system.

Now you are armed with improved diag...
Forum: maintenance & nonperformance 08-16-2019, 04:01 PM
Replies: 29
Views: 1,284
Posted By ZVOLV
Do you have power to the injectors???!

Do you have power to the injectors???!
Forum: maintenance & nonperformance 08-16-2019, 02:31 PM
Replies: 19
Views: 751
Posted By ZVOLV
,

Ok so you have traced the problem down to a fuel related issue since it runs on brake cleaner. You are close! Don't give up.

The engine should stay running on brake cleaner.

Crank sensor may...
Forum: maintenance & nonperformance 08-16-2019, 12:11 PM
Replies: 29
Views: 1,284
Posted By ZVOLV
A test lamp should be used to test the positive...

A test lamp should be used to test the positive side of a circuit. A meter can show 12v, but there may not be enough current to operate the circuit

I recently did a training class where we had to...
Forum: maintenance & nonperformance 08-16-2019, 11:59 AM
Replies: 29
Views: 1,284
Posted By ZVOLV
Do you have injector power!?? Test lamp to...

Do you have injector power!?? Test lamp to injector positive to ground.







With a test lamp backprobed between the two injector terminals.
Forum: maintenance & nonperformance 08-15-2019, 04:53 PM
Replies: 19
Views: 751
Posted By ZVOLV
Do you have pulse at the coil negative??!!

Do you have pulse at the coil negative??!!
Forum: maintenance & nonperformance 08-15-2019, 04:04 PM
Replies: 29
Views: 1,284
Posted By ZVOLV
Do you have injector pulse?!!

Do you have injector pulse?!!
Forum: maintenance & nonperformance 08-15-2019, 12:33 PM
Replies: 29
Views: 1,284
Posted By ZVOLV
Injector pulse? Did you install the correct...

Injector pulse?

Did you install the correct resistance injectors or put in a resistor pack (if needed)?
Forum: maintenance & nonperformance 08-14-2019, 06:40 PM
Replies: 8
Views: 531
Posted By ZVOLV
At the shop, a support dolly goes under the...

At the shop, a support dolly goes under the drivetrain and then the car gets lifted off the engine/trans.

A tip, always lower the boom before moving an engine on a cherry picker. We had one fall...
Forum: maintenance & nonperformance 08-14-2019, 06:21 PM
Replies: 8
Views: 531
Posted By ZVOLV
On a 740 it works great since you can pull the...

On a 740 it works great since you can pull the radiator core support. On a 240 it's welded in.

A good load leveler will help. The cheap ones bind. They help, don't work well, but it's a step...
Forum: maintenance & nonperformance 08-14-2019, 06:07 PM
Replies: 19
Views: 751
Posted By ZVOLV
Disconnecting the connector just eliminates the...

Disconnecting the connector just eliminates the component from the circuit.

Backprobe just prevents damage to the terminals. I front probe only with the proper test probe. Stuffing meter leads...
Forum: maintenance & nonperformance 08-14-2019, 03:28 PM
Replies: 19
Views: 751
Posted By ZVOLV
With computer circuits, a high impedance test...

With computer circuits, a high impedance test lamp should be used. (Approx 14 ohms). But since your car has a resistor pack, I don't see why a low impedance test lamp couldn't be used.

I would...
Forum: maintenance & nonperformance 08-13-2019, 11:37 PM
Replies: 19
Views: 751
Posted By ZVOLV
No helper is needed. Apply 12v to the starter...

No helper is needed. Apply 12v to the starter solenoid with a length of wire. There's a small blue/yellow to the starter- apply 12v here.

Backprobe the test lamp between the injector terminals....
Forum: maintenance & nonperformance 08-13-2019, 06:10 PM
Replies: 19
Views: 751
Posted By ZVOLV
You need a test lamp. Injector click on OBD mode...

You need a test lamp. Injector click on OBD mode isn't a good test. One guy here recently had rotten injector wiring at the ballast pack and had injector "click" on OBD test mode but inop injectors...
Forum: maintenance & nonperformance 08-13-2019, 03:29 PM
Replies: 19
Views: 751
Posted By ZVOLV
TPS won't cause a no start. If it runs on...

TPS won't cause a no start.

If it runs on brake cleaner that means ignition is OK and you gotta diag fuel.

Do you have a test lamp?! I would be checking next for power to the injectors. A noid...
Forum: maintenance & nonperformance 08-12-2019, 01:52 PM
Replies: 53
Views: 2,235
Posted By ZVOLV
Ball joints are usually easy to remove by...

Ball joints are usually easy to remove by slamming a big hammer against the control arm (not the stud).
Forum: maintenance & nonperformance 08-10-2019, 02:45 AM
Replies: 12
Views: 695
Posted By ZVOLV
Click my signature. Try brake cleaner.

Click my signature. Try brake cleaner.
Forum: maintenance & nonperformance 08-09-2019, 01:22 PM
Replies: 9
Views: 745
Posted By ZVOLV
Do diag. Got a test lamp? Lamp to coil negative...

Do diag. Got a test lamp? Lamp to coil negative the ground. Crank. Blink? If not, diag ignition.
Forum: maintenance & nonperformance 08-08-2019, 06:32 PM
Replies: 12
Views: 695
Posted By ZVOLV
Wiggle test the hall sensor wiring when it's...

Wiggle test the hall sensor wiring when it's running and see if it dies. These have hall sensors, right?
Forum: maintenance & nonperformance 08-08-2019, 03:36 PM
Replies: 12
Views: 695
Posted By ZVOLV
It could be the powerstage. Put a test lamp...

It could be the powerstage.

Put a test lamp between coil negative and ground and see if it blinks during a no start= no spark.

Do you have a test lamp??
Forum: maintenance & nonperformance 08-08-2019, 01:37 PM
Replies: 12
Views: 695
Posted By ZVOLV
The car runs so I guess it must work SOMETIMES.

The car runs so I guess it must work SOMETIMES.
Forum: maintenance & nonperformance 08-08-2019, 12:23 PM
Replies: 12
Views: 695
Posted By ZVOLV
Inspect the hall sensor on the dist.

Inspect the hall sensor on the dist.
Forum: maintenance & nonperformance 08-06-2019, 04:49 PM
Replies: 3
Views: 373
Posted By ZVOLV
Reverse lights always on: there's likely shorted...

Reverse lights always on: there's likely shorted wiring in the tranny tunnel.
Forum: maintenance & nonperformance 08-06-2019, 11:41 AM
Replies: 6
Views: 475
Posted By ZVOLV
I've seen threads where it ends up being the...

I've seen threads where it ends up being the ground wires at the intake manifold.

Resistance test and do a voltage drop test on them.

Inspect and drag test the terminals for the circuit...
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 09:29 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.