home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.05 seconds.
Search: Posts Made By: lummert
Forum: maintenance & nonperformance Yesterday, 08:05 PM
Replies: 6
Views: 109
Posted By lummert
Maybe a rust hole or a dipstick tube leak.

Maybe a rust hole or a dipstick tube leak.
Forum: performance & modifications Yesterday, 08:03 PM
Replies: 45
Views: 2,293
Posted By lummert
I don't have a fresh O2 sensor, but I have 2...

I don't have a fresh O2 sensor, but I have 2 spare OE O2 sensors, The O2 sensor is switching, I've checked for that.
Forum: performance & modifications Yesterday, 12:57 PM
Replies: 45
Views: 2,293
Posted By lummert
I used a dwell meter to check for injector...

I used a dwell meter to check for injector duty-cycle using the 6 Cyclinder scale. got 21 degrees or 35% duty-cycle at idle. This is with adjusting the AMM pot screw to just a hair rich (LED...
Forum: performance & modifications Yesterday, 10:29 AM
Replies: 45
Views: 2,293
Posted By lummert
I made my LED tool with a large 12 volt LED from...

I made my LED tool with a large 12 volt LED from Radio Shack. This LED has a built in resistor, so addingbresistors isn't needed. It has been my experience that adjusting the AMM pot screw effects...
Forum: maintenance & nonperformance 11-13-2018, 09:11 PM
Replies: 4
Views: 123
Posted By lummert
This is why brass drifts are available.

This is why brass drifts are available.
Forum: maintenance & nonperformance 11-13-2018, 09:05 PM
Replies: 5
Views: 140
Posted By lummert
There was a bulb out relay in the rear of 88 765...

There was a bulb out relay in the rear of 88 765 that I bypassed after it burned out. The front bulb out relay is still functional. The rear bulb out relay on the 760/940SE/960 wagon is found behind...
Forum: maintenance & nonperformance 11-13-2018, 07:43 PM
Replies: 15
Views: 233
Posted By lummert
Don't forget about the flywheel/flexplate.

Don't forget about the flywheel/flexplate.
Forum: maintenance & nonperformance 11-12-2018, 08:58 AM
Replies: 7
Views: 263
Posted By lummert
Borrow or run down to Harbor Freight to get a...

Borrow or run down to Harbor Freight to get a fuel pressure test kit. When you have this kit in front of you you'll see how the test fitting connects to the schrader valve.
Forum: performance & modifications 11-11-2018, 05:15 PM
Replies: 26
Views: 632
Posted By lummert
Replacement copper alloy brake lines of various...

Replacement copper alloy brake lines of various lengths are still available. Try Autozone online.
Forum: performance & modifications 11-10-2018, 03:47 PM
Replies: 45
Views: 2,293
Posted By lummert
These are my calculations: 0 280 155 811...

These are my calculations:

0 280 155 811 injectors:
34.3 lbs/hr @ 43.5 psi
360.5 cc/min @ 3.0 bar

32.48 lbs/hr @ 39 psi
341.36 cc/min @ 2.7 bar

Idle pressure with 2.7 bar fpr: 30 psi
Forum: performance & modifications 11-09-2018, 12:47 PM
Replies: 45
Views: 2,293
Posted By lummert
Finally got the Schrader valve hose replaced on...

Finally got the Schrader valve hose replaced on my fuel pressure tester. 0 280 160 225 - 2.5 Bar fuel pressure regulator from BMW 325e pressure test results:

39 psi w/o vacuum hose connected
30...
Forum: performance & modifications 11-08-2018, 12:10 PM
Replies: 6
Views: 438
Posted By lummert
The heat and AC in my 88 765 is Harrison France.

The heat and AC in my 88 765 is Harrison France.
Forum: performance & modifications 11-08-2018, 09:09 AM
Replies: 6
Views: 438
Posted By lummert
The rear shocks depends on whether the car is...

The rear shocks depends on whether the car is early with a solid rear axle, or later with multi-link rear suspension. The front struts should be the same as ABS equipped 740/760/940/92-94 960.
Forum: maintenance & nonperformance 11-07-2018, 06:50 PM
Replies: 6
Views: 306
Posted By lummert
What about the hose connecting the pump to the...

What about the hose connecting the pump to the sending unit. Was the intank pump installed using the correct type of submersible fuel hose?
Forum: maintenance & nonperformance 11-07-2018, 12:51 PM
Replies: 2
Views: 271
Posted By lummert
Mastercraft MC-440 Tires

Last month I purchased 2 of the tires used, and yesterday I purchased 2 more used.
They are the same as Cooper Starfire RS-C 2.0, which was easier to find specifications for. They are manufactured...
Forum: performance & modifications 11-07-2018, 11:17 AM
Replies: 45
Views: 2,293
Posted By lummert
Yesterday I tried advancing the ignition timing a...

Yesterday I tried advancing the ignition timing a bit. The idle improved. I then adjusted the AMM baseline setting until the LED was almost constantly lit, but still blinking. I then hooked up a...
Forum: maintenance & nonperformance 11-05-2018, 09:25 PM
Replies: 6
Views: 576
Posted By lummert
One thing you wouldn't think of is the main head...

One thing you wouldn't think of is the main head light relay. Its the retangular relay on the relay panel under the passenger underside of dash.
Forum: maintenance & nonperformance 11-05-2018, 09:20 PM
Replies: 17
Views: 581
Posted By lummert
A 1991 940 SE could present an issue with getting...

A 1991 940 SE could present an issue with getting a key made.
Forum: performance & modifications 11-05-2018, 07:51 PM
Replies: 45
Views: 2,293
Posted By lummert
0 280 155 811 specs from Bosch... 3.5 bar...

0 280 155 811 specs from Bosch...
3.5 bar operating pressure
282 grams/min @ 3.5 bar
261.1 grams/min @ 3 bar
373 cc/min @ 3 bar
15* spray angle
8*-24* spray area amount
92 Design type...
Forum: performance & modifications 11-05-2018, 06:17 PM
Replies: 45
Views: 2,293
Posted By lummert
Specification for the BMW 325e FPR is 38 psi.

Specification for the BMW 325e FPR is 38 psi.
Forum: performance & modifications 11-05-2018, 06:04 PM
Replies: 45
Views: 2,293
Posted By lummert
Today I swapped the BMW engine temperature sensor...

Today I swapped the BMW engine temperature sensor [0 280 130 023] back to the correct OE sensor [0 280 130 026]. The engine then ran so rich that I couldn't adjust the AMM baseline idle setting. But...
Forum: performance & modifications 11-04-2018, 09:41 PM
Replies: 45
Views: 2,293
Posted By lummert
Not a good idea to install Bosch GEN III injector...

Not a good idea to install Bosch GEN III injector using pintle caps. The injectors are shorter requiring a yellow spacer leaving no possibility to install the pintle caps. Installing the injector...
Forum: performance & modifications 11-04-2018, 03:01 PM
Replies: 45
Views: 2,293
Posted By lummert
Yes, I've read this.

Yes, I've read this.
Forum: performance & modifications 11-03-2018, 12:53 PM
Replies: 45
Views: 2,293
Posted By lummert
I checked the AMM between pins 2 and 3 with my...

I checked the AMM between pins 2 and 3 with my multimeter and came up with 4.5 ohms. According to LH2.2/2.4 Fuel Management Information **Updated** from Bentley Manual the resistance between pins 2...
Forum: performance & modifications 11-02-2018, 09:10 PM
Replies: 45
Views: 2,293
Posted By lummert
Figured out how to modify pintle caps to work on...

Figured out how to modify pintle caps to work on Bosch GEN III injectors with recessed tips. Use the lower barrel of a Pilot G-2 gel pen. Press the pintle cap onto the threaded part of the barrel....
Forum: performance & modifications 10-31-2018, 06:10 PM
Replies: 45
Views: 2,293
Posted By lummert
Swapping back to the 0 280 150 934 white-top...

Swapping back to the 0 280 150 934 white-top injectors didn't go as planned. One of the injectors was dead. Swapped back to the 0 280 155 811 white giants. Swapped back to the 3 bar fuel pressure...
Forum: maintenance & nonperformance 10-31-2018, 03:27 PM
Replies: 8
Views: 525
Posted By lummert
http://www.brickboard.com/FAQ/700-900/FAQPDFVersio...

http://www.brickboard.com/FAQ/700-900/FAQPDFVersions/EngineOBDCodes.pdf
Forum: performance & modifications 10-31-2018, 03:18 PM
Replies: 45
Views: 2,293
Posted By lummert
If the AMM is adjusted to 004 ohms (380 ohms...

If the AMM is adjusted to 004 ohms (380 ohms starting point) with Bosch White Giant injectors and 2.5 Bar fuel pressure regulator do I need to do anything with the ignition timing? I'm thinking that...
Forum: performance & modifications 10-31-2018, 12:39 PM
Replies: 45
Views: 2,293
Posted By lummert
Managed to find washer and pintle cap kits at...

Managed to find washer and pintle cap kits at Advance Auto. $1.29 plus tax for 8 kits. Next is a O-ring kit. About $4.49 for 12 o-rings.

My car is being really thirsty with the White Giant...
Forum: maintenance & nonperformance 10-30-2018, 05:51 PM
Replies: 33
Views: 6,039
Posted By lummert
Try using dish soap in the water when using Bon...

Try using dish soap in the water when using Bon Ami. It works well on stainless pots.
Forum: performance & modifications 10-30-2018, 05:42 PM
Replies: 35
Views: 1,269
Posted By lummert
I was going to suggest cooper spray.

I was going to suggest cooper spray.
Forum: performance & modifications 10-30-2018, 03:12 PM
Replies: 45
Views: 2,293
Posted By lummert
Still looking for comments on reinstalling the 0...

Still looking for comments on reinstalling the 0 280 150 934 - 30 lbs/hr @ 43.5 psi (315 cc/min @ 3 Bar) injectors. These injectors came from a Supercharged Buick 3.8L V6. They are high-resistance...
Forum: performance & modifications 10-30-2018, 02:54 PM
Replies: 35
Views: 1,269
Posted By lummert
Cheap cardboard exhaust manifold gaskets have...

Cheap cardboard exhaust manifold gaskets have been known to burn out. Spend the time to locate the better quality gaskets.
Forum: maintenance & nonperformance 10-28-2018, 03:31 PM
Replies: 33
Views: 6,039
Posted By lummert
Bosch wiper blades have always given me good...

Bosch wiper blades have always given me good service. Not all Aero wipers will work as the wiper arm can't hold enough tension due to the blade not being tall enough where it secures to the wiper arm.
Forum: maintenance & nonperformance 10-28-2018, 03:29 PM
Replies: 22
Views: 566
Posted By lummert
You should be diagnosing the fuel pump relay due...

You should be diagnosing the fuel pump relay due to the fact that you were able to start your car by bypassing this relay. The fuel ECU grounds the fuel pump relay. The fuel ECU could have an issue.
Forum: maintenance & nonperformance 10-28-2018, 03:22 PM
Replies: 6
Views: 576
Posted By lummert
The tail lights have ground wires connecting to...

The tail lights have ground wires connecting to nearby chassis ground.
Forum: maintenance & nonperformance 10-27-2018, 08:06 PM
Replies: 22
Views: 796
Posted By lummert
Make sure you're using a good oil. Such as...

Make sure you're using a good oil. Such as 15W-40, if weather permits. Shell Rotella now has T5 15W-40 which is Synthetic Blend (lower pour point).
Forum: performance & modifications 10-27-2018, 08:02 PM
Replies: 45
Views: 2,293
Posted By lummert
Tested the 2 spare 0 280 150 934 injectors. They...

Tested the 2 spare 0 280 150 934 injectors. They passed, so I now have 4 good injectors out of 6.

Now the big question...Do I keep running the GEN III 0 280 155 811 White-top injectors flowing...
Forum: performance & modifications 10-26-2018, 08:45 PM
Replies: 45
Views: 2,293
Posted By lummert
I pressure tested the four Bosch 0 280 150 934...

I pressure tested the four Bosch 0 280 150 934 injectors that I was previously running at 20 psi. Two of the four leaked down within 5 minutes.
Forum: maintenance & nonperformance 10-25-2018, 06:43 PM
Replies: 141
Views: 4,604
Posted By lummert
Water pump gasket and top seal kit is available...

Water pump gasket and top seal kit is available from Felpro for about $1.49. But I've not been able to find a square cut seal for the water pipe at the back of the pump (I used two o-rings for this).
Forum: maintenance & nonperformance 10-25-2018, 06:39 PM
Replies: 141
Views: 4,604
Posted By lummert
CV Joint grease is handy to have around.

CV Joint grease is handy to have around.
Forum: performance & modifications 10-25-2018, 04:47 PM
Replies: 45
Views: 2,293
Posted By lummert
I'm trying to devise a test to check the Bosch 0...

I'm trying to devise a test to check the Bosch 0 280 150 943 injector that I took out for leaks. I know I should have tested the injectors for leak down before pulling them from the B230 fuel rail....
Forum: performance & modifications 10-25-2018, 04:39 PM
Replies: 30
Views: 1,197
Posted By lummert
Unit body construction. Just cut the body off at...

Unit body construction. Just cut the body off at the rockers and do the same with the Jeep Cherokee. Install Volvo body onto Jeep chassis. Keep us updated on your progress.
Forum: maintenance & nonperformance 10-25-2018, 04:33 PM
Replies: 5
Views: 468
Posted By lummert
I've found it to be easier to do this on the...

I've found it to be easier to do this on the ground when doing this on my 88 765. Remove the mount and everything attaching to it from the underside of the car.
Forum: maintenance & nonperformance 10-25-2018, 04:29 PM
Replies: 17
Views: 1,042
Posted By lummert
All I got when I tried it was "pageok".

All I got when I tried it was "pageok".
Forum: maintenance & nonperformance 10-25-2018, 04:28 PM
Replies: 13
Views: 1,185
Posted By lummert
The linings on the parking brake shoes of my 88...

The linings on the parking brake shoes of my 88 765 had came off and made so much noise that I had to pull into shopping center and pull the rotor to investigate. I found the linings from both...
Forum: maintenance & nonperformance 10-25-2018, 01:11 PM
Replies: 19
Views: 798
Posted By lummert
Does the motor oil smell of gasoline?

Does the motor oil smell of gasoline?
Forum: maintenance & nonperformance 10-24-2018, 06:48 PM
Replies: 141
Views: 4,604
Posted By lummert
I've always used Permatex Type 2 non-hardening...

I've always used Permatex Type 2 non-hardening sealer.
Forum: performance & modifications 10-23-2018, 05:02 PM
Replies: 22
Views: 3,127
Posted By lummert
Info I found shows 740 (1985-1989) Turbo in...

Info I found shows 740 (1985-1989) Turbo in Portugal used B200ET. B200FT was used 1991-1998. Shows B200FT has lambda sensor and diagnostics.
Forum: performance & modifications 10-23-2018, 04:06 PM
Replies: 45
Views: 2,293
Posted By lummert
Update: Tried the 0 280 155 811 injectors...

Update:

Tried the 0 280 155 811 injectors with the 3 bar FPR again. Unable to properly adjust the AMM with these injectors @ 3 bar. swapped back to the 2.5 bar FPR.

Noticed something else...I...
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 06:44 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.