home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.09 seconds.
Search: Posts Made By: ZVOLV
Forum: performance & modifications Today, 12:52 AM
Replies: 20
Views: 362
Posted By ZVOLV
Green tops are low rez injectors. If you dont run...

Green tops are low rez injectors. If you dont run a rez pack= fried ECU.

MAF=AMM

Toughest part of the swap will be the oil feed, oil drain and the exhaust downpipe.
Forum: performance & modifications Yesterday, 11:25 AM
Replies: 20
Views: 362
Posted By ZVOLV
Grab the resistor pack for those stock injectors....

Grab the resistor pack for those stock injectors. On driver fender by the battery. Cut a good pigtail for it. And snip a MAF wiring pigtail too!
Forum: performance & modifications 01-16-2019, 04:55 PM
Replies: 58
Views: 4,083
Posted By ZVOLV
Here ya go: https://youtu.be/YJgZHAsK4hs

Here ya go:


https://youtu.be/YJgZHAsK4hs
Forum: maintenance & nonperformance 01-16-2019, 03:59 PM
Replies: 79
Views: 4,382
Posted By ZVOLV
Nice! A test lamp may have revealed a poor...

Nice!

A test lamp may have revealed a poor amount of current. A meter can show 12v, but there may not be enough current to operate the circuit. A test lamp may NOT have illuminated.

Or, maybe...
Forum: maintenance & nonperformance 01-12-2019, 08:27 PM
Replies: 17
Views: 444
Posted By ZVOLV
Your vehicle has antennae?

Your vehicle has antennae?
Forum: maintenance & nonperformance 01-11-2019, 09:31 PM
Replies: 79
Views: 4,382
Posted By ZVOLV
Do you have power to the hall sensor?

Do you have power to the hall sensor?
Forum: maintenance & nonperformance 01-11-2019, 06:23 PM
Replies: 13
Views: 504
Posted By ZVOLV
A ticking noise on acceleration can be exhaust...

A ticking noise on acceleration can be exhaust leak at the cylinder head to exhaust manifold gaskets.
Forum: maintenance & nonperformance 01-10-2019, 10:10 PM
Replies: 13
Views: 455
Posted By ZVOLV
Buy a noid light from IPD. Got a test lamp?...

Buy a noid light from IPD.

Got a test lamp? A meter?
Forum: maintenance & nonperformance 01-09-2019, 04:44 PM
Replies: 8
Views: 308
Posted By ZVOLV
Good diag.

Good diag.
Forum: maintenance & nonperformance 01-07-2019, 04:45 PM
Replies: 29
Views: 906
Posted By ZVOLV
With the B204FT exhaust manifold you gotta be...

With the B204FT exhaust manifold you gotta be careful about clearances against stiff like the block, intake hose, heater pipe, oil return, etc. Once you start changing turbine housings the wastegate...
Forum: maintenance & nonperformance 01-02-2019, 05:28 PM
Replies: 9
Views: 393
Posted By ZVOLV
With no speedo input there can be a high idle...

With no speedo input there can be a high idle after freeway runs.
Forum: showroom 12-31-2018, 07:27 PM
Replies: 176
Views: 36,171
Posted By ZVOLV
Question I found the answer using.....Google.

I found the answer using.....Google.
Forum: maintenance & nonperformance 12-31-2018, 02:28 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Does it run yet? Swdefiend- This is not a...

Does it run yet?

Swdefiend- This is not a "computer related circuit" so the test lamp is still best.

https://forums.tbforums.com/picture.php?albumid=398&pictureid=3586
...
Forum: performance & modifications 12-28-2018, 10:20 PM
Replies: 16
Views: 622
Posted By ZVOLV
Plumbing leaks would likely cause stumble going...

Plumbing leaks would likely cause stumble going into boost. I have 20 quid on busted turbine housing!
Forum: performance & modifications 12-28-2018, 05:26 PM
Replies: 16
Views: 622
Posted By ZVOLV
Disconnect the wastegate hose and go for a drive...

Disconnect the wastegate hose and go for a drive and see what happens. If it still doesn'tover boost, you could wire the wastegate flap shut and try again.

I am still voting damaged turbine...
Forum: maintenance & nonperformance 12-28-2018, 04:17 PM
Replies: 8
Views: 324
Posted By ZVOLV
Hmmm....a long time ago I believe I had success...

Hmmm....a long time ago I believe I had success with a 740 cluster sliding the digits to the left.
Forum: performance & modifications 12-27-2018, 11:45 PM
Replies: 16
Views: 622
Posted By ZVOLV
A cracked/melted turbine housing is very likely. ...

A cracked/melted turbine housing is very likely.

Pull the down pipe and inspect.

Even with my wastegate hose disconnected my 13c would only make about the same- melted/cracked housing was the...
Forum: maintenance & nonperformance 12-27-2018, 10:25 PM
Replies: 8
Views: 324
Posted By ZVOLV
You slide the numbers left with a pick and then...

You slide the numbers left with a pick and then they freespool.
Forum: maintenance & nonperformance 12-26-2018, 02:45 PM
Replies: 3
Views: 242
Posted By ZVOLV
Take the belts off one at a time and see if it is...

Take the belts off one at a time and see if it is still there.
Forum: maintenance & nonperformance 12-23-2018, 01:41 PM
Replies: 19
Views: 882
Posted By ZVOLV
Nice. Thanks for posting back. I fixed my no...

Nice. Thanks for posting back. I fixed my no start once with no diag tools by just swapping the powerstage also.
Forum: performance & modifications 12-20-2018, 06:40 PM
Replies: 99
Views: 3,366
Posted By ZVOLV
I just installed a new turbo and have the...

I just installed a new turbo and have the wastegate puck just flapping open in the breeze. The car can barely make it up a steep hill.
Forum: maintenance & nonperformance 12-20-2018, 02:41 PM
Replies: 21
Views: 1,004
Posted By ZVOLV
Have you tried setting it on fire?

Have you tried setting it on fire?
Forum: maintenance & nonperformance 12-19-2018, 05:36 PM
Replies: 14
Views: 519
Posted By ZVOLV
You can resistance test the clock spring and see...

You can resistance test the clock spring and see if its open. Spin it and check too.
Forum: maintenance & nonperformance 12-18-2018, 06:54 PM
Replies: 52
Views: 15,948
Posted By ZVOLV
Last shop I worked at we just added dye to the...

Last shop I worked at we just added dye to the coolant we pumped out of a drum.
Forum: maintenance & nonperformance 12-18-2018, 05:37 PM
Replies: 14
Views: 538
Posted By ZVOLV
Air hammer to slam the gland nut off. 1/2" impact...

Air hammer to slam the gland nut off. 1/2" impact to slam the nut off/on.
Forum: maintenance & nonperformance 12-18-2018, 03:52 PM
Replies: 12
Views: 462
Posted By ZVOLV
Checked for burned terminals. The fact that...

Checked for burned terminals. The fact that somebody was in there may mean its burned up a few of them before.
Forum: maintenance & nonperformance 12-18-2018, 02:04 PM
Replies: 12
Views: 462
Posted By ZVOLV
:woowoo: Glad you got it.

:woowoo:

Glad you got it.
Forum: maintenance & nonperformance 12-17-2018, 08:34 PM
Replies: 12
Views: 462
Posted By ZVOLV
Hang on.... You could check if there is...

Hang on....

You could check if there is current at the MAF blue yellow wire/key on. Use a test lamp.

If not current there, the relay is bad or the circuit, or the computer. You could use a...
Forum: maintenance & nonperformance 12-17-2018, 07:58 PM
Replies: 12
Views: 462
Posted By ZVOLV
The ECU controls the relay by grounding the...

The ECU controls the relay by grounding the control circuit of the relay. You can take a meter and check if the computer is grounding the relay when cranking. It also should ground the relay key-on...
Forum: maintenance & nonperformance 12-17-2018, 07:13 PM
Replies: 14
Views: 519
Posted By ZVOLV
Did you let the clock spring un-coil? It may have...

Did you let the clock spring un-coil? It may have been damaged.

There is a trick to getting it back on correctly if it's been un-coiled: Count how many turns it takes to completely wind it up and...
Forum: maintenance & nonperformance 12-17-2018, 07:10 PM
Replies: 12
Views: 462
Posted By ZVOLV
I have a known good B234F ECU if you want it. $50...

I have a known good B234F ECU if you want it. $50 shipped.
Forum: maintenance & nonperformance 12-17-2018, 07:04 PM
Replies: 14
Views: 538
Posted By ZVOLV
To get ball joints to let go just slam the...

To get ball joints to let go just slam the control arm with my favorite tool- the mini sledge! They will fall free if you put enough man-strength into the swing.
Forum: maintenance & nonperformance 12-17-2018, 12:43 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
There is a fuel pump fuse, right? 10 seconds with...

There is a fuel pump fuse, right? 10 seconds with a test lamp back probing the fuse would be where I would start.

I diagnosed a crank-no start in 10 minutes this weekend with a can of brake...
Forum: maintenance & nonperformance 12-15-2018, 07:39 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Time to bust out the labscope on this one.

Time to bust out the labscope on this one.
Forum: maintenance & nonperformance 12-15-2018, 07:12 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
I'm not going to argue with you. I am just going...

I'm not going to argue with you. I am just going to tell you that you are wrong.

A meter is NOT the best tool for the job.
Forum: maintenance & nonperformance 12-15-2018, 05:42 PM
Replies: 17
Views: 1,128
Posted By ZVOLV
O2 has 1. Signal 2. Heater positive 3....

O2 has

1. Signal
2. Heater positive
3. Heater ground
Forum: maintenance & nonperformance 12-15-2018, 05:31 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
There is no need to bypass s*** when you know how...

There is no need to bypass s*** when you know how to use a wiring diagram and a test lamp.
Forum: maintenance & nonperformance 12-15-2018, 01:28 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
I measured 12v, using a meter, on a window...

I measured 12v, using a meter, on a window regulator circuit recently. Replaced regulator. Didn't fix it. Rechecked with a test lamp-did not illuminate. It was a poor connection in the door jamb....
Forum: maintenance & nonperformance 12-14-2018, 09:39 PM
Replies: 13
Views: 604
Posted By ZVOLV
Thumbs up Be careful. Its bearing preload. Amount of...

Be careful.

Its bearing preload. Amount of inch/lb. required to TURN the flange. I got it wrong the first time and the opinion was flopping around on the test drive!

Your pinion could also be...
Forum: maintenance & nonperformance 12-14-2018, 09:35 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Test lamp!!! Dont use a meter. One strand of wire...

Test lamp!!! Dont use a meter. One strand of wire can pass 12v and show as that on a meter, but won't run a pump.

You are close. It's either a dead pump/s, the fuel pump circuit, injector...
Forum: maintenance & nonperformance 12-14-2018, 08:56 PM
Replies: 13
Views: 604
Posted By ZVOLV
1989 740 GLE open diff 4.10 pinion: ...

1989 740 GLE open diff 4.10 pinion:

http://www.forums.turbobricks.com/picture.php?albumid=212&pictureid=3572
Forum: maintenance & nonperformance 12-14-2018, 08:50 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Noid light. 30 seconds. No brain required to...

Noid light. 30 seconds. No brain required to confirm power to injectors AND pulse. Every Turtlebricker needs one!
Forum: maintenance & nonperformance 12-14-2018, 08:29 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Runs on ether means the fuel system is NOT...

Runs on ether means the fuel system is NOT working. The ECU is part of the "fuel system". The ECU may be bad. Prob not.

Runs on ether= mechanicals and spark are ok. Time to shake down the fuel...
Forum: maintenance & nonperformance 12-14-2018, 07:52 PM
Replies: 17
Views: 1,128
Posted By ZVOLV
.9v, as mentioned, means stuck rich. Try...

.9v, as mentioned, means stuck rich.

Try the measurement again on a hot engine and with the sensor unplugged. Measuring on the o2 sensor side. It makes it's own voltage.

Can't hurt to measure...
Forum: maintenance & nonperformance 12-14-2018, 07:45 PM
Replies: 3
Views: 500
Posted By ZVOLV
Thumbs up There should be two nips there. The hoses go to...

There should be two nips there. The hoses go to the charcoal canister.

Smog sucks. Raw fuel vapors cause a lot of smog. Fix it.
Forum: maintenance & nonperformance 12-14-2018, 07:22 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
$5 noid light from IPD works great. $20 noid...

$5 noid light from IPD works great. $20 noid light kit is sold at auto stores. It takes 30 seconds to pull one out of the drawer and plug it in and then crank.

You can also put a screwdriver...
Forum: maintenance & nonperformance 12-14-2018, 06:17 PM
Replies: 43
Views: 1,404
Posted By ZVOLV
Test lamp> power to injectors? Power to coil? ...

Test lamp> power to injectors? Power to coil?

Spark?


Run on brake cleaner? Click my sig
Forum: maintenance & nonperformance 12-14-2018, 02:08 PM
Replies: 8
Views: 473
Posted By ZVOLV
If it were me, I'd put a used pump on. I've...

If it were me, I'd put a used pump on. I've installed up to three or four reman pumps on a car before I got a good one that didn't leak or moan. We have see the rack do it too.

Start with a few...
Forum: maintenance & nonperformance 12-14-2018, 12:41 PM
Replies: 13
Views: 604
Posted By ZVOLV
Pinion uses a crush sleeve that will need to be...

Pinion uses a crush sleeve that will need to be replaced. It took heavy tools to compress the crush sleeve and then an INCH POUND torque wrench to get spec correct.
Forum: maintenance & nonperformance 12-13-2018, 06:03 PM
Replies: 9
Views: 858
Posted By ZVOLV
I had the head off my 1991 740 recently and...

I had the head off my 1991 740 recently and poured the cylinders full of decarbonizing liquid. Only one cylinder kept liquid in it overnight= 3 cylinders have worn rings/cylinders. This engine also...
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 07:14 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.