home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.02 seconds.
Search: Posts Made By: Cwazywazy
Forum: maintenance & nonperformance 01-14-2020, 10:34 PM
Replies: 6
Views: 318
Posted By Cwazywazy
https://i.imgur.com/wraAnbfh.jpg Crusty. ...

https://i.imgur.com/wraAnbfh.jpg

Crusty.

So I did an ohm check on the wiring (between alt and terminals) before I took it apart again and I got ~1ohm on the ground, but I got 0ohms on the...
Forum: maintenance & nonperformance 01-13-2020, 11:52 PM
Replies: 6
Views: 318
Posted By Cwazywazy
Harness is bout 3 years old. Will do all wiring...

Harness is bout 3 years old. Will do all wiring checks tomorrow, last time I had alternator problems it was actually the wiring which is why it now has two ground wires.
Forum: maintenance & nonperformance 01-13-2020, 10:30 PM
Replies: 6
Views: 318
Posted By Cwazywazy
Denso problemos..

100a denso on my '82 240. Been using this alt for a couple years now, thinking it had ended a string of alternator problems that I was having..

Last week I was driving it and noticed it wasn't...
Forum: maintenance & nonperformance 12-10-2019, 11:17 PM
Replies: 8
Views: 581
Posted By Cwazywazy
I made the same mistake and my synchro dogs fell...

I made the same mistake and my synchro dogs fell out completely. I got it back together without further disassembly but it was a royal pain. The ring goes on the inside of the dogs and then you have...
Forum: projects & restorations 12-05-2019, 11:09 PM
Replies: 259
Views: 62,511
Posted By Cwazywazy
I can't believe it hasn't sold yet.

I can't believe it hasn't sold yet.
Forum: projects & restorations 12-03-2019, 02:35 AM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Car is running great. Running on Deka 80lb...

Car is running great. Running on Deka 80lb injectors now cause I was hitting 95% duty on the cheapie 42lbs. I found flow/voltage numbers somewhere for an 016, plugged those in, and that fixed my...
Forum: maintenance & nonperformance 11-27-2019, 12:26 AM
Replies: 68
Views: 11,475
Posted By Cwazywazy
Going off memory, IAC pin 2 is power (12v I...

Going off memory, IAC pin 2 is power (12v I think) and pins 1/3 are connected to ground by the ECU to pull it towards open or close. If you haven't already, put the meter on resistance and see if the...
Forum: maintenance & nonperformance 11-22-2019, 03:20 PM
Replies: 68
Views: 11,475
Posted By Cwazywazy
I dunno if you've already tried it, but have you...

I dunno if you've already tried it, but have you messed with the TPS? Does it cut with it disconnected?
Forum: aftermarket engine management 11-21-2019, 12:02 AM
Replies: 26
Views: 2,998
Posted By Cwazywazy
#1 I have the main side of the fuel relay,...

#1 I have the main side of the fuel relay, triggered by the key, powering mine.

#3 Do it on MS just so you can fine tune it from the seat.

#4 I think the trick to a good MS install is to use...
Forum: performance & modifications 11-20-2019, 11:46 AM
Replies: 11
Views: 2,524
Posted By Cwazywazy
Yeah, it's 80 bucks cheaper.

Yeah, it's 80 bucks cheaper.
Forum: projects & restorations 11-10-2019, 01:08 AM
Replies: 504
Views: 166,126
Posted By Cwazywazy
https://i.imgur.com/Cg8khweh.jpg ...

https://i.imgur.com/Cg8khweh.jpg
https://i.imgur.com/5QDV1fjh.jpg
https://i.imgur.com/C2qq59Eh.jpg
https://i.imgur.com/hn3zl4Uh.jpg
https://i.imgur.com/eb2Q06Wh.jpg

I chopped 1 coil off each...
Forum: projects & restorations 11-08-2019, 12:39 AM
Replies: 504
Views: 166,126
Posted By Cwazywazy
I put in new injectors and cranked up the fun...

I put in new injectors and cranked up the fun valve. The rear suspension pretty much immediately started making even more noises. So I figured I've been putting it off long enough and yanked the turd...
Forum: maintenance & nonperformance 11-01-2019, 10:41 PM
Replies: 6
Views: 1,049
Posted By Cwazywazy
If you can hear the solenoid clicking (ign on,...

If you can hear the solenoid clicking (ign on, engine off, in 4th) it's probably time for a rebuild or replacement.
Forum: projects & restorations 10-26-2019, 10:30 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
I basically started over with my fuel tuning. I...

I basically started over with my fuel tuning. I made a new tune that was MAF only and worked the MAF curve into something that actually works, then I added speed density as secondary for fine tuning....
Forum: projects & restorations 10-23-2019, 05:42 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Do you remember that time I completely destroyed...

Do you remember that time I completely destroyed my engine because I couldn't hear it knocking? I need a knock sensor. But, actually, it doesn't matter cause knocksense still works without anything...
Forum: projects & restorations 10-22-2019, 02:18 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
MAF is wired in and working. Throttle response is...

MAF is wired in and working. Throttle response is sooooo much better now. I logged for a little bit, hit 120% duty cycle at like 14psi. Intake temp stayed at about 60f while I was moving.
...
Forum: maintenance & nonperformance 10-22-2019, 11:32 AM
Replies: 63
Views: 6,740
Posted By Cwazywazy
I usually put at least 1000mi a month on my '82...

I usually put at least 1000mi a month on my '82 turbo. I've been stranded by it like three times this year, but every time was close to home. I drove it 600mi a couple months ago and, other than the...
Forum: projects & restorations 10-21-2019, 10:48 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
I drove around on MS a couple times. I got the...

I drove around on MS a couple times. I got the idle AFRs pretty good, but it seems to be misfiring at idle. Dunno what's up with that. Also I gotta figure out how to get the IAC to work with this...
Forum: projects & restorations 10-19-2019, 04:10 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Hehehe. <iframe width="560" height="315"...

Hehehe.

<iframe width="560" height="315" src="https://www.youtube.com/embed/0Z6L6e6NFw4" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture"...
Forum: projects & restorations 10-19-2019, 12:16 AM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Making progress. I stared at wiring diagrams for...

Making progress. I stared at wiring diagrams for awhile, made these connectors, did what the DIYautotune article told me to do, and gave it a try. I got it communicating with my laptop and pushed...
Forum: projects & restorations 10-17-2019, 12:28 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
I think I'm gonna try and get it working with...

I think I'm gonna try and get it working with just MAP and IAT but I'm still reading the manuals and deciding how I'm gonna go at it.

I gave it 12v but it wouldn't communicate because I don't have...
Forum: projects & restorations 10-16-2019, 11:09 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
https://i.imgur.com/wEXxE5eh.jpg I have no...

https://i.imgur.com/wEXxE5eh.jpg

I have no idea how to finagle this doohickey.

MS2 v3.0 set up for LH2.4 use. Plan is to figure out how to set it up for 2.2 and make a plug and play harness so...
Forum: performance & modifications 10-13-2019, 12:42 PM
Replies: 10
Views: 1,202
Posted By Cwazywazy
Hardware store rubber pipe coupler with a plastic...

Hardware store rubber pipe coupler with a plastic pipe cap glued into one end, hole drilled in that and a tire valve in said hole.

<iframe width="560" height="315"...
Forum: projects & restorations 10-11-2019, 11:03 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
I added an itty bitty glasspack. This let me...

I added an itty bitty glasspack. This let me change the angle of the exhaust a bit so it wouldn't rattle against the spring, which is an issue I've had since swapping the exhaust from the wagon, and...
Forum: maintenance & nonperformance 10-03-2019, 06:35 PM
Replies: 4
Views: 782
Posted By Cwazywazy
Does it have gas?

Does it have gas?
Forum: projects & restorations 09-28-2019, 11:53 AM
Replies: 13
Views: 1,514
Posted By Cwazywazy
https://i.imgur.com/lZzLgJRh.jpg

https://i.imgur.com/lZzLgJRh.jpg
Forum: maintenance & nonperformance 09-25-2019, 03:45 PM
Replies: 3
Views: 625
Posted By Cwazywazy
Pinch off the coolant hoses with a couple vice...

Pinch off the coolant hoses with a couple vice grips, you'll be good.
Forum: performance & modifications 09-24-2019, 03:34 PM
Replies: 15
Views: 1,080
Posted By Cwazywazy
You'll have to bypass the ballast resistor since...

You'll have to bypass the ballast resistor since orange tops are high impedance.
Forum: performance & modifications 09-24-2019, 02:48 PM
Replies: 15
Views: 1,080
Posted By Cwazywazy
Orange tops and stock 007 MAF were fine up to...

Orange tops and stock 007 MAF were fine up to about 16psi for me on a 15g.
Forum: projects & restorations 09-18-2019, 04:39 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
My torque rod bushings and TABs are wrecked, but...

My torque rod bushings and TABs are wrecked, but they were fine a few months ago and it's been shuddering in first ever since I swapped the M47 for an M46 in the wagon, which had all new bushings....
Forum: projects & restorations 09-12-2019, 08:44 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Is it possible a missing bell housing dowel pin...

Is it possible a missing bell housing dowel pin would cause my first gear shudder? It fell out like two years ago.

I got new clips for the windshield bezel and managed to crack my windshield...
Forum: projects & restorations 09-10-2019, 02:52 PM
Replies: 1,500
Views: 364,325
Posted By Cwazywazy
I have cheapo stock engine/trans mounts in my car...

I have cheapo stock engine/trans mounts in my car plus your thick rod. It's honestly fine for daily use. Definitely noticeable at idle but I have no issue living with it.
Forum: projects & restorations 08-28-2019, 04:28 PM
Replies: 672
Views: 257,958
Posted By Cwazywazy
I'm the opposite. I like a turbo that looks nice...

I'm the opposite. I like a turbo that looks nice and cozy.

Fiberglass wrap does suck to work with though..
Forum: projects & restorations 08-28-2019, 03:21 PM
Replies: 672
Views: 257,958
Posted By Cwazywazy
Would it be easier to wrap the downpipe?

Would it be easier to wrap the downpipe?
Forum: projects & restorations 08-23-2019, 10:18 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Transmission #4 is installed. Came from a diesel...

Transmission #4 is installed. Came from a diesel 240, no idea now many miles are on it, and it works perfectly. Overdrive engaged at 20mph no problem. I put in some brand new shifter parts and a knob...
Forum: performance & modifications 08-23-2019, 08:18 PM
Replies: 4
Views: 850
Posted By Cwazywazy
Maybe cause of the NA injectors?

Maybe cause of the NA injectors?
Forum: performance & modifications 08-22-2019, 10:01 PM
Replies: 14
Views: 1,352
Posted By Cwazywazy
Why not stock replacements if they're all saggy? ...

Why not stock replacements if they're all saggy?

Are your tires rubbing because they're bigger than stock or is that just a 140 thing? Missing bump stops?
Forum: maintenance & nonperformance 08-22-2019, 09:46 PM
Replies: 12
Views: 1,446
Posted By Cwazywazy
Aight, so just outta curiosity, the longer diesel...

Aight, so just outta curiosity, the longer diesel shifter must mean the trans sits further forwards in a diesel? But whats with the different output flange?
Forum: maintenance & nonperformance 08-22-2019, 09:18 PM
Replies: 12
Views: 1,446
Posted By Cwazywazy
Already removed shim, both type J, and I'm using...

Already removed shim, both type J, and I'm using a speedo cable. I'll find myself a 28mm socket tomorrow for the output. Manual diesels had a 3.56 rear end, right?
Forum: maintenance & nonperformance 08-22-2019, 08:54 PM
Replies: 12
Views: 1,446
Posted By Cwazywazy
I'm installing an M46 from a diesel 240. There...

I'm installing an M46 from a diesel 240. There was a shim of some sort on the end of the input shaft, I got that off, and it seems the output flange is about a half inch shorter than it should be. If...
Forum: projects & restorations 08-16-2019, 11:49 PM
Replies: 259
Views: 62,511
Posted By Cwazywazy
The important thing is that you didn't arrive on...

The important thing is that you didn't arrive on a flatbed.

https://i.imgur.com/LAcoL9Qh.jpg
Forum: maintenance & nonperformance 08-16-2019, 01:50 PM
Replies: 23
Views: 3,566
Posted By Cwazywazy
Yeah. My method is a 1/4" extension and I tap it...

Yeah. My method is a 1/4" extension and I tap it in all the way around until the little ball hits the RMS housing.
Forum: performance & modifications 08-13-2019, 11:22 PM
Replies: 4
Views: 759
Posted By Cwazywazy
That oil looks like it came from the PCV to me,...

That oil looks like it came from the PCV to me, on the right one. I'd run the 13t just cause it's a lil bit bigger.
Forum: projects & restorations 08-12-2019, 03:58 PM
Replies: 259
Views: 62,511
Posted By Cwazywazy
Nice to see you might keep this one.

Nice to see you might keep this one.
Forum: maintenance & nonperformance 08-12-2019, 12:55 AM
Replies: 18
Views: 1,148
Posted By Cwazywazy
$10-20 on Amazon with prime shipping. ...

$10-20 on Amazon with prime shipping.
...
Forum: maintenance & nonperformance 08-11-2019, 11:36 PM
Replies: 18
Views: 1,148
Posted By Cwazywazy
Probably a good idea to replace it. Id say chuck...

Probably a good idea to replace it. Id say chuck in an electric pump as a test/permanent replacement. A clickety clack can't cost much at a parts store.

Does it run better momentarily after...
Forum: projects & restorations 08-10-2019, 12:06 AM
Replies: 504
Views: 166,126
Posted By Cwazywazy
https://i.imgur.com/nGvU8cjh.jpg I'm really...

https://i.imgur.com/nGvU8cjh.jpg

I'm really starting to hate these things..

Cobbled my pile of transmission trash into one mostly functional M46 and installed it. Only problem is a fairly...
Forum: projects & restorations 08-08-2019, 05:02 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
Uhhh.. Firewall braces. That's it. Every bushing...

Uhhh.. Firewall braces. That's it. Every bushing is 37 years old. There's nothing wrong with the suspension and I've got more important things to fix/improve right now. Although it is gonna need...
Forum: projects & restorations 08-08-2019, 04:03 PM
Replies: 504
Views: 166,126
Posted By Cwazywazy
oops https://i.imgur.com/9fWawoQh.jpg ...

oops

https://i.imgur.com/9fWawoQh.jpg
https://i.imgur.com/48gUXt1h.jpg
Forum: maintenance & nonperformance 08-07-2019, 12:38 PM
Replies: 6
Views: 773
Posted By Cwazywazy
In my experience taking the intake off isn't...

In my experience taking the intake off isn't necessary but it sure does make it easier.
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 07:27 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.