home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 19 of 19
Search took 0.00 seconds.
Search: Posts Made By: nathaninwa
Forum: performance & modifications 04-29-2013, 11:40 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
its not really. when the t stat is closed, it...

its not really. when the t stat is closed, it circs back to the pump via the head, so when the spring heats up and the t stat opens, its opening with coolant flow, so it alsmot helps it. and...
Forum: performance & modifications 10-17-2011, 02:24 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
There is a 1/4 inch pipe hole in the block...

There is a 1/4 inch pipe hole in the block between cylinders 1-2. Almost a short circuit on the pump when the system is open. I aslo pull water from the back of the head on the intake side.
Forum: performance & modifications 10-17-2011, 12:29 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
Ever since I drilled the holes in the head, ran...

Ever since I drilled the holes in the head, ran that programmable 3/8 bypass, and run the stock balancer with stock large water pump pulley.......there have been zero issues. Probably 12 dyno...
Forum: performance & modifications 06-01-2011, 07:58 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
And get it line honed, decked, and new aux...

And get it line honed, decked, and new aux bearings then have 2 more sleeves installed from normal 200k engine wear, your looking at almost 600, so wont do that again. I wish this thread was...
Forum: performance & modifications 05-25-2011, 08:11 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
Its an alum radiator from a Ford Aerostar.. Its...

Its an alum radiator from a Ford Aerostar.. Its a 2 core setup. I welded some large tanks on it. Off the top of my head, core size is like 22x19. Its about the size of the NPR intercooler..
Forum: performance & modifications 04-08-2011, 09:14 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
I dont know about pressure....but I can tell you...

I dont know about pressure....but I can tell you that with the stock harmonic balancer....and the early larger water pump pulley...the cooling is a good match for low idle speed cooling and I bet...
Forum: performance & modifications 03-09-2011, 02:04 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
Qwkswde......I did the group a mod way back in...

Qwkswde......I did the group a mod way back in the first page I think. But I did not add the extra holes along the exhaust side......just drilled the blind holes on the head...but present in the...
Forum: performance & modifications 03-09-2011, 10:20 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
double post

double post
Forum: performance & modifications 03-09-2011, 10:18 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
I tried both Volvo pulleys on the stock balancer....

I tried both Volvo pulleys on the stock balancer. The larger one still popped the plugs, so I made a pulley from a sbc that was 1 inch larger in diamter. Worked out to be close to 1800rpm slower...
Forum: performance & modifications 03-09-2011, 02:50 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
Along with drilling holes in my head where the...

Along with drilling holes in my head where the gasket had some, but it did not, I just got done doing this.


Here are some pics showing my water bypass from the head, and the passengers block. ...
Forum: performance & modifications 11-13-2010, 11:59 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
The Hepu that Im running, looks like it has S...

The Hepu that Im running, looks like it has S shaped impeller blades on a cast brass wheel.
Forum: performance & modifications 11-03-2010, 10:07 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
When my head gos back on, Ill be going back to...

When my head gos back on, Ill be going back to the larger of the volvo pulleys to help cooling at idle in traffic (its about an inch smaller than the one I have right now). Ill also be installed...
Forum: performance & modifications 10-13-2010, 12:48 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
mine are hella stiff. gm poly tranny mounts at...

mine are hella stiff. gm poly tranny mounts at all 3 locations. if you look in the dyno video.....my motor does not move. i was thinkin of all the vibration could be dampened a little by...
Forum: performance & modifications 10-13-2010, 01:47 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
qwkswede....what kind of motor and tranny mounts...

qwkswede....what kind of motor and tranny mounts are you running?
Forum: performance & modifications 10-11-2010, 01:54 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
When I blew mine out the first time, passenger...

When I blew mine out the first time, passenger side front was flush with block, and popped the rear 2 out. Drivers popped the front one and the next 2 were flushed with block.

They all were...
Forum: performance & modifications 10-10-2010, 12:28 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
my cover plates. ...

my cover plates.

http://i816.photobucket.com/albums/zz88/nathaninwa/Mobile%20Uploads/0912001812.jpg

http://i816.photobucket.com/albums/zz88/nathaninwa/Mobile%20Uploads/0603001932.jpg
Forum: performance & modifications 10-09-2010, 05:05 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
i would agree john.......i ended up putting...

i would agree john.......i ended up putting plates over the hole shibang for easness. i like the ideaa of one plate or the small washer bit but trying to do that in the car blows......so i chose...
Forum: performance & modifications 10-09-2010, 12:19 AM
Replies: 229
Views: 296,236
Posted By nathaninwa
So as a fellow TB'er that has blown his freeze...

So as a fellow TB'er that has blown his freeze plugs twice....im going to ramble a bit.

3 stages to this problem.

1....bought 91 940 with 17x,xxx miles. stock balancer and stock "small" wp...
Forum: performance & modifications 10-08-2010, 02:47 PM
Replies: 229
Views: 296,236
Posted By nathaninwa
this is a thread of interest......my problems...

this is a thread of interest......my problems seem to have gone away and ive just been lazy at updating my build thread. when i get home tonight ill update here what im running.
Showing results 1 to 19 of 19

 
Forum Jump

All times are GMT -4. The time now is 01:20 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.