home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.16 seconds.
Search: Posts Made By: dl242gt
Forum: maintenance & nonperformance 10-24-2020, 01:01 PM
Replies: 2
Views: 112
Posted By dl242gt
Yes, people have modified their fuel delivery...

Yes, people have modified their fuel delivery system to only have one pump. They usually use a fuel injection rated intank pump to supply all the fuel. The purpose of two pumps as stock is to provide...
Forum: performance & modifications 10-23-2020, 03:14 PM
Replies: 3
Views: 199
Posted By dl242gt
I use the Simons Sport System that Skandix sells....

I use the Simons Sport System that Skandix sells. Not stainless but it's such good quality the first one lasted about 7 years. You can also look at the JT tuning stuff. https://www.jt-tuning.se/
Forum: performance & modifications 10-23-2020, 03:10 PM
Replies: 34
Views: 1,741
Posted By dl242gt
I had a true track installed in my 82 turbo and...

I had a true track installed in my 82 turbo and using Redline Synthetic gear oil the rear started to whine. I took it back to the shop and they suggested going to a dino oil. So I put the Lucas GL 5...
Forum: maintenance & nonperformance 10-23-2020, 03:04 PM
Replies: 22
Views: 727
Posted By dl242gt
Have you installed the stock lower brace? I think...

Have you installed the stock lower brace? I think 960s came with it but US model 740/940 cars didn't.
Forum: maintenance & nonperformance 10-23-2020, 03:02 PM
Replies: 33
Views: 3,099
Posted By dl242gt
Once you open the air flow sensor it seems to...

Once you open the air flow sensor it seems to flow much more evenly than idle or the old test. Way to go on the FD rebuild. There used to be a Volvo Troubleshooting guide that IPD used to sell. Lots...
Forum: maintenance & nonperformance 10-23-2020, 02:57 PM
Replies: 16
Views: 856
Posted By dl242gt
I read to do that here. I think it was the...

I read to do that here. I think it was the smokey100 guy that wrote about it. For the end coming through the sheet metal hole I used the right angle stock 240 turbo elbow with the horn removed. I...
Forum: maintenance & nonperformance 10-23-2020, 02:52 PM
Replies: 8
Views: 270
Posted By dl242gt
Should be able to use a low power test light and...

Should be able to use a low power test light and test for the trigger signal on the integrated amp coil driver unit on the left inner fender. The rpm sensor triggers the control unit in the car. The...
Forum: maintenance & nonperformance 10-22-2020, 05:56 PM
Replies: 16
Views: 856
Posted By dl242gt
Another easy upgrade is to unsnap the four legs...

Another easy upgrade is to unsnap the four legs of the plastic thermostat bracket from the air box. Then use the open hot air intake for a second cold air intake that enters from the hole in the...
Forum: maintenance & nonperformance 10-22-2020, 01:17 PM
Replies: 1
Views: 196
Posted By dl242gt
You'll be fine. As long as you use the correct...

You'll be fine. As long as you use the correct type of sensor which is a heated one.
Forum: maintenance & nonperformance 10-21-2020, 07:06 PM
Replies: 8
Views: 270
Posted By dl242gt
I've had brand new cranks sensors bad out of the...

I've had brand new cranks sensors bad out of the box.
Forum: maintenance & nonperformance 10-21-2020, 02:26 PM
Replies: 8
Views: 270
Posted By dl242gt
You can check for codes with the Rex/Regina...

You can check for codes with the Rex/Regina setup. But my initial guess at the issue would be your engine speed sensor. You mentioned you were working in that area doing the heater hoses. It's easy...
Forum: performance & modifications 10-21-2020, 12:43 PM
Replies: 16
Views: 500
Posted By dl242gt
What gold injectors did you use? I have a member...

What gold injectors did you use? I have a member here that is asking about kjet injectors.
Forum: maintenance & nonperformance 10-21-2020, 12:28 PM
Replies: 5
Views: 254
Posted By dl242gt
Lubricate the door latches with Wurth HHS Plus....

Lubricate the door latches with Wurth HHS Plus. It's a spray grease that leaves a lubricating film. It's a wonderful product.
Forum: maintenance & nonperformance 10-21-2020, 12:24 PM
Replies: 20
Views: 816
Posted By dl242gt
Yes, it's a good idea to pump the pedal a few...

Yes, it's a good idea to pump the pedal a few times before bleeding. As Lando says. It's very important to close the bleeder before the pedal returns. In addition dont' forget that if it's an old...
Forum: performance & modifications 10-19-2020, 06:53 PM
Replies: 12
Views: 813
Posted By dl242gt
I too use a 205-60-15 for my spare. It's on a 740...

I too use a 205-60-15 for my spare. It's on a 740 steelie and just fits in the area. If I set up another spare I will probably use something like Kyle suggests. That size is also a lighter tire. The...
Forum: maintenance & nonperformance 10-19-2020, 06:44 PM
Replies: 7
Views: 359
Posted By dl242gt
Glad you got that sorted out. I used to own an...

Glad you got that sorted out. I used to own an early 65 911 and a couple of 356 coupes many moons ago. I miss such fun cars.
Forum: maintenance & nonperformance 10-18-2020, 08:55 PM
Replies: 7
Views: 359
Posted By dl242gt
I'd suggest you do have some type of intake air...

I'd suggest you do have some type of intake air leak if the idle is that high. It could also be the idle switch is now out of adjustment or failed so the idle control system doesn't know the throttle...
Forum: performance & modifications 10-17-2020, 05:36 PM
Replies: 20
Views: 7,895
Posted By dl242gt
Thanks Kyle. That little B21 sure does love...

Thanks Kyle. That little B21 sure does love making high rpm power. It took me floating the valves and dropping intake no.2 from a broken retainer to finally install the 405 head. :cool:
Forum: maintenance & nonperformance 10-17-2020, 05:26 PM
Replies: 4
Views: 469
Posted By dl242gt
The Volvo ones are Bendix branded on many of the...

The Volvo ones are Bendix branded on many of the cars I've worked on. I have a spare or two stashed and was thinking I may need to replace mine in my 93 wagon.
Forum: maintenance & nonperformance 10-16-2020, 07:06 PM
Replies: 1
Views: 367
Posted By dl242gt
Acceleration is helped by the fuel pressure...

Acceleration is helped by the fuel pressure regulator on the fuel rail. I would suggest a fuel pressure test. If the pressure is a bit high or low. That can cause some hesitation. Another though t is...
Forum: maintenance & nonperformance 10-16-2020, 07:00 PM
Replies: 14
Views: 571
Posted By dl242gt
There is no system fuse in the engine bay in kjet...

There is no system fuse in the engine bay in kjet turbo. But fuse 13 in the fuse box turns on most everything and can cause a cranking but no start issue.
Forum: maintenance & nonperformance 10-16-2020, 06:21 PM
Replies: 20
Views: 816
Posted By dl242gt
A pressure bleeder is a small pressure tank like...

A pressure bleeder is a small pressure tank like a pressure sprayer you use to spray weed killer. You fill the tank with brake fluid and connect to the brake reservoir. Pressurize the tank upto about...
Forum: maintenance & nonperformance 10-16-2020, 06:17 PM
Replies: 42
Views: 2,357
Posted By dl242gt
You probably need to regap or replace your spark...

You probably need to regap or replace your spark plugs. It's called spark blowout and under high load with too large of a plug gap it blows the spark out. Use .028" or you can even reduce it to .026"...
Forum: maintenance & nonperformance 10-16-2020, 06:11 PM
Replies: 2
Views: 333
Posted By dl242gt
You'll be fine with the high strength loctite. I...

You'll be fine with the high strength loctite. I used to flatten the washer in a vise and reuse it.
Forum: maintenance & nonperformance 10-16-2020, 06:08 PM
Replies: 14
Views: 571
Posted By dl242gt
Cranking is turning over. Does the engine rotate...

Cranking is turning over. Does the engine rotate when you try to start? Or is it not rotating? These are very straight forward to figure out. I'd love to have another 245 turbo. I used to have an 82....
Forum: maintenance & nonperformance 10-16-2020, 06:01 PM
Replies: 15
Views: 1,112
Posted By dl242gt
65ftlb is correct for early 740/760 with their...

65ftlb is correct for early 740/760 with their wimpy wheel studs. I've never seen writing on the early ones I've worked on. People were popping those wheel studs all the time so Volvo decided to help...
Forum: maintenance & nonperformance 10-15-2020, 09:23 PM
Replies: 20
Views: 816
Posted By dl242gt
I've never had much success gravity bleeding on a...

I've never had much success gravity bleeding on a 240. I've had that work great on British sports cars on the brakes and the clutch system. But for the 240 series after having a few too many...
Forum: maintenance & nonperformance 10-15-2020, 09:17 PM
Replies: 6
Views: 436
Posted By dl242gt
A is the motor to my knowledge. It's what you...

A is the motor to my knowledge. It's what you unscrew to replace the odometer gears under it.
Forum: maintenance & nonperformance 10-15-2020, 09:14 PM
Replies: 42
Views: 2,357
Posted By dl242gt
Well done. Enjoy!

Well done. Enjoy!
Forum: performance & modifications 10-11-2020, 06:40 PM
Replies: 18
Views: 1,116
Posted By dl242gt
Good for the money yellow fog lights are Hella...

Good for the money yellow fog lights are Hella 550 in amber. Also if you want to spend more and get a higher quality product. Cibie makes really nice amber fog lights.
Forum: maintenance & nonperformance 10-11-2020, 06:01 PM
Replies: 3
Views: 490
Posted By dl242gt
This is the Wurth version of what is linked...

This is the Wurth version of what is linked above. It was worked very well for me. Their stuff can be a bit more expensive but it is always high quality. ...
Forum: maintenance & nonperformance 10-11-2020, 05:55 PM
Replies: 27
Views: 1,278
Posted By dl242gt
You can also gently tap on the metal lines and...

You can also gently tap on the metal lines and the pressure regulators with a small hammer to break loose any air that is stuck.

What kind of brake fluid did you use? Your car requires DOT4. The...
Forum: maintenance & nonperformance 10-11-2020, 05:45 PM
Replies: 42
Views: 2,357
Posted By dl242gt
Well, you know from the factory these cars are...

Well, you know from the factory these cars are low boost cars. The stock boost on my B21FT was only 6.5psi and even when you put the intercooler kit on it with turbo+ the main part of the available...
Forum: maintenance & nonperformance 10-11-2020, 05:37 PM
Replies: 3
Views: 388
Posted By dl242gt
Here is what has worked well for me. Gap at the...

Here is what has worked well for me. Gap at the stock .028" Not in any favorite order.
NGK BPR6ES also the NGK V plugs
Denso copper plugs. Denso Iridium.
Autolite 64 and Autolite AP64
Bosch...
Forum: maintenance & nonperformance 10-09-2020, 07:47 PM
Replies: 6
Views: 755
Posted By dl242gt
If you are looking for a good rattle can wheel...

If you are looking for a good rattle can wheel paint. The Wurth silver wheel paint is good stuff.
Forum: maintenance & nonperformance 10-09-2020, 07:42 PM
Replies: 14
Views: 743
Posted By dl242gt
The important location is the two filament...

The important location is the two filament location. Many people use the 1157 for the two filament bulb when it should be the lower wattage bulb 1034. For flashers the 1156 is fine as well as with...
Forum: maintenance & nonperformance 10-09-2020, 02:03 PM
Replies: 42
Views: 2,357
Posted By dl242gt
When your engine is cold. Remove the intake hose...

When your engine is cold. Remove the intake hose to the compressor and check the turbo shaft for play. It may be you have a worn out turbo as suggested. You are looking for very little play. If it...
Forum: performance & modifications 10-09-2020, 01:42 PM
Replies: 24
Views: 1,135
Posted By dl242gt
Been using a v15 n/a in my 93 wagon for about ten...

Been using a v15 n/a in my 93 wagon for about ten years now. The engine is basically stock otherwise. Makes power and torque all the way to redline. It's so nice having torque at 3500 rpm and above....
Forum: maintenance & nonperformance 10-09-2020, 01:18 PM
Replies: 14
Views: 743
Posted By dl242gt
Use 1156 for the single filament bulbs. Use 1034...

Use 1156 for the single filament bulbs. Use 1034 for the two filament bulbs.
Forum: performance & modifications 10-08-2020, 07:25 PM
Replies: 24
Views: 1,135
Posted By dl242gt
Well done! Thanks for documenting how quickly the...

Well done! Thanks for documenting how quickly the M cam loses torque and lets you down. Especially with a manual trans.
Forum: maintenance & nonperformance 10-08-2020, 03:54 PM
Replies: 8
Views: 467
Posted By dl242gt
Yes, indeed. I've never had one of the old...

Yes, indeed. I've never had one of the old version starters fail. The one in my 82 turbo is original at 336k miles.
Forum: maintenance & nonperformance 10-07-2020, 02:41 PM
Replies: 8
Views: 467
Posted By dl242gt
I just had to replace my starter for an...

I just had to replace my starter for an intermittent issue last year. It wouldn't crank the car when hot. So you drive somewhere and then it won't start. I would bang on the solenoid with my breaker...
Forum: maintenance & nonperformance 10-07-2020, 02:38 PM
Replies: 1
Views: 316
Posted By dl242gt
I'd check the intake manifold gasket. That one...

I'd check the intake manifold gasket. That one can be a very sneaky leak. Also injector seals when leaking vacuum can make a low rpm misfire. Did you gap the plugs to .028"? I wouldn't trust them to...
Forum: maintenance & nonperformance 10-07-2020, 02:34 PM
Replies: 21
Views: 1,030
Posted By dl242gt
To test the crank signal. You test the INPUT wire...

To test the crank signal. You test the INPUT wire to the ignition amp. Not the red/white output wire. I think it may be pin 5 that is the trigger input signal from the ezk computer. If there is no...
Forum: performance & modifications 10-01-2020, 07:02 PM
Replies: 20
Views: 7,895
Posted By dl242gt
From personal experience. With an enem V15 turbo...

From personal experience. With an enem V15 turbo cam. There is no 'flattening of the power' at high rpms. My engine makes power from just above idle to 7k rpms. It still has more to go but for the...
Forum: maintenance & nonperformance 10-01-2020, 06:27 PM
Replies: 10
Views: 850
Posted By dl242gt
An air chisel will separate spot welds.

An air chisel will separate spot welds.
Forum: maintenance & nonperformance 10-01-2020, 06:21 PM
Replies: 9
Views: 863
Posted By dl242gt
You can use the shelf on the manifold to mate up...

You can use the shelf on the manifold to mate up to the Volvo T3 housing. The smaller studs will work. Another hardware choice is to use a stepped stud that is 8mm on one half and 10mm on the other...
Forum: performance & modifications 10-01-2020, 02:33 PM
Replies: 9
Views: 693
Posted By dl242gt
If you lower your car just enough to make the...

If you lower your car just enough to make the control arms level with the ground. You have set the car up so the roll center isn't destroyed and the car can handle very well with the spring changes...
Forum: maintenance & nonperformance 09-29-2020, 09:40 PM
Replies: 7
Views: 622
Posted By dl242gt
You can make up some small brackets that hold the...

You can make up some small brackets that hold the spring into the lower perch. That way when it hangs it holds the bottom of the spring onto the perch. Or put a limit strap so the strut can only hang...
Forum: maintenance & nonperformance 09-29-2020, 08:39 PM
Replies: 4
Views: 513
Posted By dl242gt
If you looked at it through the grill. You see a...

If you looked at it through the grill. You see a vertical bar that has a bracket on it to bolt the light on. The vertical bar is recessed back several inches from being flush with the grill.
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 06:20 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.