hackster
Active member
- Joined
- Jun 17, 2011
- Location
- Portland Or.
Well I did a horrible job the last few days of taking photos....sorry for the build thread.
I received the Spectrum replacement fuel tank on Monday and got to work mounting up my new fuel system. The tank is far nicer than expected, even came painted a satin silver that will totally work with my scheme here so saved me some time and money.
Located where the new setup will go, marked the location and drilled a 3.25" hole for the new assembly to drop into. This puts the pump out of the way of the stock float for the fuel level and gives me a great location for the Holley Hydramat to lay out as well as miss the factory filler neck too.
Followed the ****ty instructions that came with the pump but it worked just fine. This is a big single pump, 450 with an internal regulator regulating the output to 60 PSI. The only fittings coming from the new pump is a supply line and a vent. The vent will be hooked to the factory filler neck opening.
The new assembly all bolted down to the tank.
I abandoned the stock fuel line connections on the tank but am utilizing it still for fuel level sender. I am waiting on caps to show up to plug them off. Should be here today, new level sender is installed as well as a new o ring and lock ring, its a clean looking setup and should be plenty for what I am doing.
Scott from STS Machine and I had been going back and forth for a few weeks on 8.8 stuff, he had some killer lazer cut brackets made for the 8.8 to 240, so while in Portland Tuesday and stopped by his place and picked them up with a 25mm front v8 sway bar. I also snagged some 3/4x3/4 heim joints, some bushings, tube and weld inserts.
I got to work yesterday, yarded out the factory Volvo rear axle and got to work locating all of the brackets and getting things tacked up. I spent a little more time than I probably should have but it all worked out.
I ditched the factory lower arms all together. It just didnt make sense, I was going to have to cut them down, buy new bushings for the front, Bens Spherical bearings for the rear and then chop off the back and plate it, then build mounts for the coilovers. It was too complicated for something so simple.
I used some Heim joints at the axle, 1.75OD bushings x3" wide and a piece of 2" .120 tubing for the front bushing at the car. a piece of 1.5" .120 DOM tubing for the lower control arm and a 1.25" weld insert for the heim. It worked awesome and I was able to just use some off the shelf 3" laser cut tabs for the lower link mounts. Now everything on the rear is more conventional.
I have rear coilovers on order, upper and lower shock tabs on order, brakes are shipped, rear ARP wheel studs are on order, I think I am making some progress.
The axle is actually under the car now at ride height, I shortened the lowers .75" and have adjustment to go longer or shorter still. Ben's comfort uppers are in place as well, they have just enough adjustment on them to make the shortened lowers work.
I am hoping that I can set this thing on its own weight next week some time with the fuel system all buttoned up and the suspension mostly buttoned up.
I am getting tired though, been busting my ass lately.
Sean
I received the Spectrum replacement fuel tank on Monday and got to work mounting up my new fuel system. The tank is far nicer than expected, even came painted a satin silver that will totally work with my scheme here so saved me some time and money.
Located where the new setup will go, marked the location and drilled a 3.25" hole for the new assembly to drop into. This puts the pump out of the way of the stock float for the fuel level and gives me a great location for the Holley Hydramat to lay out as well as miss the factory filler neck too.
Followed the ****ty instructions that came with the pump but it worked just fine. This is a big single pump, 450 with an internal regulator regulating the output to 60 PSI. The only fittings coming from the new pump is a supply line and a vent. The vent will be hooked to the factory filler neck opening.
The new assembly all bolted down to the tank.
I abandoned the stock fuel line connections on the tank but am utilizing it still for fuel level sender. I am waiting on caps to show up to plug them off. Should be here today, new level sender is installed as well as a new o ring and lock ring, its a clean looking setup and should be plenty for what I am doing.
Scott from STS Machine and I had been going back and forth for a few weeks on 8.8 stuff, he had some killer lazer cut brackets made for the 8.8 to 240, so while in Portland Tuesday and stopped by his place and picked them up with a 25mm front v8 sway bar. I also snagged some 3/4x3/4 heim joints, some bushings, tube and weld inserts.
I got to work yesterday, yarded out the factory Volvo rear axle and got to work locating all of the brackets and getting things tacked up. I spent a little more time than I probably should have but it all worked out.
I ditched the factory lower arms all together. It just didnt make sense, I was going to have to cut them down, buy new bushings for the front, Bens Spherical bearings for the rear and then chop off the back and plate it, then build mounts for the coilovers. It was too complicated for something so simple.
I used some Heim joints at the axle, 1.75OD bushings x3" wide and a piece of 2" .120 tubing for the front bushing at the car. a piece of 1.5" .120 DOM tubing for the lower control arm and a 1.25" weld insert for the heim. It worked awesome and I was able to just use some off the shelf 3" laser cut tabs for the lower link mounts. Now everything on the rear is more conventional.
I have rear coilovers on order, upper and lower shock tabs on order, brakes are shipped, rear ARP wheel studs are on order, I think I am making some progress.
The axle is actually under the car now at ride height, I shortened the lowers .75" and have adjustment to go longer or shorter still. Ben's comfort uppers are in place as well, they have just enough adjustment on them to make the shortened lowers work.
I am hoping that I can set this thing on its own weight next week some time with the fuel system all buttoned up and the suspension mostly buttoned up.
I am getting tired though, been busting my ass lately.
Sean