• Hello Guest, welcome to the initial stages of our new platform!
    You can find some additional information about where we are in the process of migrating the board and setting up our new software here

    Thank you for being a part of our community!

think it will spool??

thelostartof

thelostartof

unbalanced chemical
300+ Club
Joined
Jun 26, 2002
Location
Apache Junction, AZ
i am tempted to just bolt it up ... BUT it would require a little custom work .. eh oh well

to the one who had this shipped to me .. looks like it made it here ok .. spins good almost no shaft play but really rusty

holset_7871.jpg


holset_7870.jpg


holset_7869.jpg


holset_7868.jpg


holset_7867.jpg


holset_7866.jpg


either way that turbine side is really not that big @ all ... the compressor is fairly larger than most i have here
 
Somewhere on the turbine housing you'll see something that tells you how big it is. 12 cm^2 is what the smallest HX35Ws were, but I have a suspicion the non-wastegated HX35s were 14 or 16 cm^2.

A TD04-13c is 6 or 7 cm^2, IIRC.

Doug's HY35W was 9 cm^2, and it didn't spool 'till 3500 or so, and though that could have been hampered by his cam, it was also helped by his header.
 
TD04-13c is a 6cm2 but also a smaller series than the TD04HL-15g/16t/18t/19t

so a 6cm2 TD04 vs a 6cm2 TD04HL are different as the HL is a larger series just like the TD05 series so a 6cm2 TD05 is larger than a TD04HL 6cm2
 
Matt Dupuis said:
Somewhere on the turbine housing you'll see something that tells you how big it is. 12 cm^2 is what the smallest HX35Ws were, but I have a suspicion the non-wastegated HX35s were 14 or 16 cm^2.

A TD04-13c is 6 or 7 cm^2, IIRC.

Doug's HY35W was 9 cm^2, and it didn't spool 'till 3500 or so, and though that could have been hampered by his cam, it was also helped by his header.
Click to expand...

no I was in full tilt by 3500rpm. It would 'spool' as low as 2000rpm (just didn't come alive to about 3000rpm). That also was when it "came on cam" as well.

that car was fun :oops:
 
Matt Dupuis said:
Doug's HY35W was 9 cm^2, and it didn't spool 'till 3500 or so, and though that could have been hampered by his cam, it was also helped by his header.
Click to expand...

nah, just reading back old posts he was hitting 14psi by 4000rpm on the stock B21FT square manifold.

said that proturbo mani brought it in 8-900rpm earlier. and then the external gate brought in evening quicker. and this was on a low compresion B21FT
 
Hank Scorpio said:
no I was in full tilt by 3500rpm. It would 'spool' as low as 2000rpm (just didn't come alive to about 3000rpm). That also was when it "came on cam" as well.

that car was fun :oops:
Click to expand...
Pardon, my bad.

Still, with the 9 cm^2 housing, I'd hope it would come in quicker than a 14 or 16 like what's shown.
 
i have a external wastegated 12cm2 hx35.... so they do come with the 12cm2 housing non internal wastgate... its believed to come off a generator... im not selling it or anything just saying. oh and the a/r on mine is stamped on the inside of one of the exhaust enteries.
 
You must log in or register to reply here.
Back
Top