home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > maintenance & nonperformance

Reply
 
Thread Tools Display Modes
Old 07-23-2012, 05:28 PM   #101
BGoins12
Board Member
 
BGoins12's Avatar
 
Join Date: Aug 2011
Location: Amherst, Ohio
Default

Anyone know how much I need to torque the bolts down for the rear main seal carrier plate?
__________________
-William
'98 S90 - 201k - Whiteblock POWAH
'97 Mazda B2300 (Ford Ranger) - 186k - 2.3/5-Speed - No POWAH
BGoins12 is offline   Reply With Quote
Old 07-23-2012, 06:07 PM   #102
vvpete
Board Member
 
Join Date: Feb 2005
Location: Land of Enchantment
Default

Quote:
Originally Posted by BGoins12 View Post
Anyone know how much I need to torque the bolts down for the rear main seal carrier plate?
IIRC they are 7 lb/ft torque.
vvpete is offline   Reply With Quote
Old 07-23-2012, 11:57 PM   #103
BGoins12
Board Member
 
BGoins12's Avatar
 
Join Date: Aug 2011
Location: Amherst, Ohio
Default

I figured it was something low, mainly because of the size of the bolts. I just tightened them and snugged them a bit, so probably around 10-12 ft/lbs. Plus I used threadlocker so they should be good for another 160k or so.
BGoins12 is offline   Reply With Quote
Old 08-04-2012, 08:17 PM   #104
smokeyfan1000
Guest
 
Default

1978-1991 240 steering column SHAFT where steering wheel retaining nut threads on is M18-1.5 thread/count.

I'm told 140s - 1977 240s have same threads/count also
  Reply With Quote
Old 08-11-2012, 08:34 PM   #105
Mueller
Board Member
 
Mueller's Avatar
 
Join Date: Oct 2004
Location: Antioch, CA
Default

Quote:
Originally Posted by BLS View Post
Didn't see the starter bolts in this FAQ. I had to cut off the heads and then lost the rest during my slow rebuild job on a 1990 240DL.
bump for starter mounting hardware....even a pic could help right now
__________________
.........
Mueller is offline   Reply With Quote
Old 10-26-2012, 02:44 PM   #106
HonestJhon
Board Member
 
HonestJhon's Avatar
 
Join Date: Aug 2005
Location: So Cal
Default

Quote:
Originally Posted by HonestJhon View Post
Flexplate hardware


Flexplate to crank and flex plate to torque converter...?
anyone? in the final stages of this build and wanted to replace the old hardware (if i even have it anymore...) involved in bolting these things on.
HonestJhon is offline   Reply With Quote
Old 10-27-2012, 03:46 PM   #107
HonestJhon
Board Member
 
HonestJhon's Avatar
 
Join Date: Aug 2005
Location: So Cal
Default

checked, dont have any spare crank bolts (none in the new motor)

if anyone has a motor laying around they could check , that would be greatly appreciated. crank bolts and torque converter bolts.
HonestJhon is offline   Reply With Quote
Old 11-05-2012, 09:15 PM   #108
HonestJhon
Board Member
 
HonestJhon's Avatar
 
Join Date: Aug 2005
Location: So Cal
Default

nothing? i havent been over to the motor to work on it for a week....but still need the info!

i'd like to be able to order something from jegs or summit....
maybe RSI stocks something?

anyone?
HonestJhon is offline   Reply With Quote
Old 11-16-2012, 03:03 PM   #109
HonestJhon
Board Member
 
HonestJhon's Avatar
 
Join Date: Aug 2005
Location: So Cal
Default

bolt that fits for the crank is m10x1.5 length, im guessing is something in the 40-50mm range.


my last resort is to order them from the dealer. i just have a feeling these are going to be in the 5-6 dollars each range.
HonestJhon is offline   Reply With Quote
Old 12-03-2012, 02:49 PM   #110
542
Board Member
 
Join Date: Nov 2010
Location: Vancouver, BC
Default

A link to anything you need to know re AN fittings
http://www.precisionenginetech.com/t...rdware-part-1/

5 pages worth of reading, bottom right of article takes you to next page (not totally obvious). Lots of photos and explanations. I find Summit, Jegs etc.. frustrating when looking for fittings as its all not in one spot and always going back and forth to compare
__________________
-----------------
542 is offline   Reply With Quote
Old 12-05-2012, 04:12 AM   #111
740tankDriver
Post-Hypnotic Sigma
 
740tankDriver's Avatar
 
Join Date: Aug 2006
Location: Under your nose.
Default

what is the thread size on the main fuel pump check valve? not the compression-seal side the thread for the check valve to the main pump.
__________________
Happy Passover!

Great Victory!
740tankDriver is offline   Reply With Quote
Old 12-11-2012, 06:04 AM   #112
cleanflametrap
Board Member
 
cleanflametrap's Avatar
 
Join Date: Sep 2009
Location: near baltimore
Default



(For Mueller)
__________________
-Art
cleanflametrap is offline   Reply With Quote
Old 02-11-2013, 02:01 AM   #113
MistrThou
Darth Mog
 
MistrThou's Avatar
 
Join Date: Oct 2004
Location: Beloit, WI
Default

From impvolvo:
Lower chassis brace for 7/900
10mm x 1.5 pitch x 25mm need 3 bolts and one 10mmx1.5 pitch nut
__________________
91 944T - Gone, 93 244+t and CR-V
Photobucket sucks...
MistrThou is offline   Reply With Quote
Old 03-04-2013, 11:58 AM   #114
J.B.
Board Member
 
Join Date: Jul 2012
Location: SE Michigan
Default

Does anyone know off hand the size & pitch of the studs/nuts on the exhaust manifold flange-to-header pipe on an NA B230? I saw the manifold studs are listed here but not the next juncture on the exhaust. Possibly even the part #'s for said three studs and copper lock washers.
__________________
1979 242GT, a work in progress.

DD: 1991 245 SE.
J.B. is offline   Reply With Quote
Old 06-17-2013, 09:58 AM   #115
cleanflametrap
Board Member
 
cleanflametrap's Avatar
 
Join Date: Sep 2009
Location: near baltimore
Default

Quote:
Originally Posted by J.B. View Post
Does anyone know off hand the size & pitch of the studs/nuts on the exhaust manifold flange-to-header pipe on an NA B230? I saw the manifold studs are listed here but not the next juncture on the exhaust. Possibly even the part #'s for said three studs and copper lock washers.
Surprised this wasn't in the thread already, and it was asked before at #81 but not yet answered.

M10 (1.5) -- nothing exotic. Don't know length, but can look up p/n: 977581
cleanflametrap is offline   Reply With Quote
Old 06-17-2013, 02:55 PM   #116
smokeyfan1000
Guest
 
Default

Quote:
Originally Posted by cleanflametrap View Post
Surprised this wasn't in the thread already, and it was asked before at #81 but not yet answered.

M10 (1.5) -- nothing exotic. Don't know length, but can look up p/n: 977581
This might help a little for part numbers.

Buying them from ww.tascaparts.com is what I did.

http://forums.turbobricks.com/showth...s+part+numbers
  Reply With Quote
Old 06-30-2013, 11:19 AM   #117
Harry Tuttle
Board Member
 
Join Date: Jun 2006
Location: in your ducts
Default

From the thread referenced above:

Quote:
Originally Posted by smokyfan1000
I think we need a "Volvo Part Number List" stickied on TB somewhere
+1 on that
__________________
I came into this game for the action, the excitement. Go anywhere, travel light, get in, get out, wherever there's trouble, a man alone


Quote:
Originally Posted by sbabbs
who cares, push start it if you have a man tranny.
Harry Tuttle is offline   Reply With Quote
Old 08-28-2013, 11:33 PM   #118
$EEKING 945 TURBO WAGON
Board Member
 
Join Date: Jan 2012
Location: 47933 Shipping ZIP; Midwest
Default Favorite quality thread pitch gauge sources? LARGE PRINT

Who sells a thread pitch gauge that has old man eyes sized readable stamped print; and useable sizes without wasting space with impractical sizes- and maybe NOT CHEESY QUALITY?

Metric/ SAE/ both?
$EEKING 945 TURBO WAGON is offline   Reply With Quote
Old 10-22-2013, 04:17 PM   #119
122power
dude
 
122power's Avatar
 
Join Date: Feb 2009
Location: Where have all the quad squares gone? VV,Ca
Default

M47 drail and fill plug 18mm x 1.5.
122power is offline   Reply With Quote
Old 11-12-2013, 09:15 PM   #120
Sir Psycho
holstrich 2.0
 
Sir Psycho's Avatar
 
Join Date: Sep 2008
Location: Austin TX
Default

What's the length of the M8x1.25 exhaust studs?
__________________
Isaac



1995 940 Turbo:
531 head, Holset HE351 @ 20 psi, Emusa External Wastegate w/screamer, Mild Steel Header, 4" Downpipe, Ostrich Emulator, IPD Turbo Cam, TTR Cam Gear, Big Piping and Intercooler, 3" Exhaust, V8 T5 soon, Synapse Synchronic BOV, AEM Wideband, 18" Pegasus, B&G Springs, Billy HD's, Chassis Bracing, Sumimoto HTR ZIII 225/40/18
Sir Psycho is offline   Reply With Quote
Old 03-26-2014, 11:04 AM   #121
cleanflametrap
Board Member
 
cleanflametrap's Avatar
 
Join Date: Sep 2009
Location: near baltimore
Default 240: some fuel sender pipe diameters

cleanflametrap is offline   Reply With Quote
Old 04-04-2014, 08:30 AM   #122
cleanflametrap
Board Member
 
cleanflametrap's Avatar
 
Join Date: Sep 2009
Location: near baltimore
Default

Quote:
Originally Posted by Sir Psycho View Post
What's the length of the M8x1.25 exhaust studs?
The M8 studs I have (240 Ti p/n 953048) are 50mm long.

cleanflametrap is offline   Reply With Quote
Old 04-04-2014, 08:33 AM   #123
cleanflametrap
Board Member
 
cleanflametrap's Avatar
 
Join Date: Sep 2009
Location: near baltimore
Default

Now, why do I have this picture?



These are the cam cover studs and the thermostat housing studs in the head (B21/23/230 best I know).
cleanflametrap is offline   Reply With Quote
Old 05-12-2014, 02:00 PM   #124
benski
Board Member
 
Join Date: Jul 2008
Location: Olympic Peninsula, Wa. State
Post

Quote:
Originally Posted by $EEKING 945 TURBO WAGON View Post
Who sells a thread pitch gauge that has old man eyes sized readable stamped print; and useable sizes without wasting space with impractical sizes- and maybe NOT CHEESY QUALITY?

Metric/ SAE/ both?
Matco tools, Part #432.
benski is offline   Reply With Quote
Old 05-17-2014, 04:37 PM   #125
Coupe' de Grace
Slowest in the West™
 
Coupe' de Grace's Avatar
 
Join Date: Mar 2005
Location: metropolitan los angeles
Default

per request:

k-jet and idle computer sensor ports on the block (near the dipstick)

12mm x 1.5mm 11mm x 1.5mm per honestjhon
3/8NPT

__________________
V A F

(1976 265dl/b27/m46 killed in battle, 1991)
(1976 265dl/b27/bw55 bring out ye dead, 2000)
(1980 262c/b28/m46 trebuchet fatality 2014)
1982 244t/b21ft/aw71 'Vicious Chicken of Bristol'
1989 780/b230ft/aw71 'Brave Sir Robin'

Last edited by Coupe' de Grace; 07-09-2014 at 02:01 PM..
Coupe' de Grace is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 01:44 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.