home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > projects & restorations

Reply
 
Thread Tools Display Modes
Old 01-29-2018, 11:48 PM   #126
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Quote:
Originally Posted by 84B23F View Post
GCP also has a bunch of vintage model parts microfiche online: http://www.gcp.se/katalog/
__________________
'63 PV Rat Rod
'93 245 16VT Classic #1141
JohnMc is online now   Reply With Quote
Old 01-31-2018, 03:56 PM   #127
84B23F
Board Member
 
84B23F's Avatar
 
Join Date: Feb 2008
Location: Kansas, USA
Default

Quote:
Originally Posted by JohnMc View Post
That one might work...

That one had a hydra-vac unit...check bore diameter, and compare. In a master setup, each chamber is exerting its own force, whereas with a slave, it is powering all wheel cylinders. Also, wheel cylinder diameter determines how much force is required. Hence, the bore diameters of Slave/Master and wheel cylinders determine how much pedal pressure is required. If your front brakes have larger pistons (surface area), then front brakes might grab before rear brakes. Vehicle's weight proportion also is factored into this equation...

If your emergency brake is fit for duty, and you have good brake lines, I'd use OEM setup.

I know 1980 GMC 7000 trucks still had a single slave cylinder, which powered a hydra-vac using a Master setup. It's called a "master cylinder," but I call it a slave.
.
84B23F is offline   Reply With Quote
Old 01-31-2018, 04:03 PM   #128
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

I was responding to your earlier post, you got two more posts in before I responded.

Quote:
Originally Posted by 84B23F View Post
Bore diameter affects hydraulic pressure. Years ago, I installed a master from a Blazer to a small pickup truck, and those brakes were touchie.

A dual circuit would be nice, but finding one that mates might be an issue.

Btw, does this Slave Cylinder fit your 544? It's much cheaper, unless S/H is high.

Just from photos, it appears your Slave Cylinder does not have a face to bolt on firewall...if true, finding a dual circuit might be hard, unless UK/Europe vehicles had that format.
The earlier PV master cylinders do bolt in, they just have a large cast in reservoir way down low on the frame, but AFAIK you can still use the late model reservoir cap that has a line fitting up to a conveniently mounted remote plastic reservoir, up where you can actually see it.
JohnMc is online now   Reply With Quote
Old 02-01-2018, 03:32 AM   #129
hiperfauto
Board Member
 
hiperfauto's Avatar
 
Join Date: Nov 2011
Location: So Cal
Default

The caps won't interchange between the early internal reservoir master cylinders and the later external reservoir masters, but there's a conversion cap available that allows you to use the early master with a remote reservoir.

http://www.skandix.de/en/spare-parts...inder/1007486/
hiperfauto is offline   Reply With Quote
Old 04-11-2018, 11:59 AM   #130
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Only thing of note with the PV lately is that I was going to drive it a few weeks ago, went to open the driver's door, and POP, something broke and the handle flopped down, the door opened but wouldn't stay shut.

I figured the spring holding the bolt out had broken (again) but when I pulled it apart not only was that broken (the POP), but apparently the body of the latch (that guides the bolt) had been broken for a while. Probably why that door latch had been so noisy and poorly working (I developed a habit of bumping the door with my shoulder to open it from inside). I'd have tried just welding the frame/case back together again, but since the rest of the latch was fairly worn (droopy door handle syndrome) I decided to just replace it.

I checked in a few places for used ones, but at $150 I decided to just spend a bit more and get a new one instead of another one that's 60 years old already. I find it mildly amusing that theyr'e still making new parts like this for PV's, I guess lots of people are willing to spend $$$ to keep them working after all these years.

New RH PV door latch, made in Poland:


Works perfectly. Not the slightest bit of slop in the door handle, no need to 'bump' the door open form inside, w00t.

Last edited by JohnMc; 04-11-2018 at 12:08 PM..
JohnMc is online now   Reply With Quote
Old 04-11-2018, 03:19 PM   #131
stick70
All the gauges
 
stick70's Avatar
 
Join Date: Sep 2006
Location: North Carolina
Default

Hell yeah! I was surprised to get a brand new latch for the 220 hatch recently. Volvo classic parts rock.
__________________
Kyle and the "Projects" -- '84 242 TI -- '66 220 S -- '89 Supra Turbo -- '84 Rabbit GTI -- '91 Honda Beat
stick70 is offline   Reply With Quote
Old 04-23-2018, 08:34 PM   #132
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Annnd now the motor has a problem. Sure don't know how that could have happened.... *ahem*

Anyhow, it's been idling a little unevenly. I tried twiddling on the DCOE's. They practically never fall out of tune like a pair of SU's can. But no joy. Checked valve clearances, no issues at all. Did a compression check and... like I suspected from listening to it crank, I'm down about 50% on #3. Not sure how accurate my ancient pressure gauge is (not at all) but 121, 122, 60, 124 is not a good pattern at all. Nope.

So I did a leak down test just to see what was fubared. After remembering to put it in gear after it repeatedly rotated the motor until #3 exhaust valve was open, I got a positive result. Air was blowing... right out the crankcase vent.

Lovely. Some sort of ring or piston issue. This happened not terribly long ago, that time it was a broken chunk on a piston:


I really don't like having two cars apart at the same time, it rather stresses my casual 'piles of parts' method, so I might just have to wait a while to tear into this and see what went wrong. Maybe this time around I'll rebuild it with some lighter weight/longer rod forged goodies.

Or... just thinking out loud, I do have a perfectly good 16V motor sitting around. The uber zoomie intake and exhaust manifolds certainly won't fit on the PV, but maybe my old log manifold would, and maybe a shortened stocker. Run low boost? 250-ish HP? Hmmm...
JohnMc is online now   Reply With Quote
Old 04-23-2018, 10:20 PM   #133
Harry Tuttle
Board Member
 
Join Date: Jun 2006
Location: in your ducts
Default

Do eet. I don't think you have enough to keep you busy...
__________________
I came into this game for the action, the excitement. Go anywhere, travel light, get in, get out, wherever there's trouble, a man alone


Quote:
Originally Posted by sbabbs
who cares, push start it if you have a man tranny.
Harry Tuttle is offline   Reply With Quote
Old 05-09-2018, 04:55 PM   #134
evolvo67
Board Member
 
evolvo67's Avatar
 
Join Date: Sep 2010
Location: Port Hadlock, Wa
Default

John, have you seen this?

evolvo67 is offline   Reply With Quote
Old 05-10-2018, 12:51 AM   #135
84B23F
Board Member
 
84B23F's Avatar
 
Join Date: Feb 2008
Location: Kansas, USA
Default

Quote:
Originally Posted by JohnMc View Post
Annnd now the motor has a problem.
Looking for a B18? It's suppose to be rebuidable... I bought it for the SU carbs
84B23F is offline   Reply With Quote
Old 05-10-2018, 07:14 AM   #136
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Nah. At the least I will keep it at a 2.1l.
JohnMc is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 10:06 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.