home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > projects & restorations

Reply
 
Thread Tools Display Modes
Old 06-07-2018, 10:41 AM   #176
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

Quote:
Originally Posted by Opgedronken View Post
Awesome to see another Dutch guy doing an M120 swap.
This post is pushing me towards going dry sump though :P.
Ah nice, you're doing one too? Not sure a dry sump is less work than this though :p
Sander is offline   Reply With Quote
Old 06-07-2018, 04:24 PM   #177
Opgedronken
Newbie
 
Join Date: Jun 2018
Default

Yeah, but in a Miata. Just joined here to follow your build :P.
Opgedronken is offline   Reply With Quote
Old 06-07-2018, 09:37 PM   #178
JohnLane
Board Member
 
Join Date: Nov 2002
Location: Northern Washington
Default

120 in a Miata.

OP Great project. Should be a nice runner. Going to have to get oil to wander back to the sump. First rule of plumbing applies.
__________________
Overkill is consistently more fun.
JohnLane is offline   Reply With Quote
Old 06-08-2018, 02:49 AM   #179
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

I'll be making a tube between the front part of the sump and the rear part. It's a bit annoying to have to do this, but the oil pump hangs under the engine in the front part of the sump so I can't make it smaller there. The tube will connect the new rear sump with the front one and goes underneath the subframe. I'll make some baffles etc in it too to prevent the oil from all moving forward during heavy braking.

Quote:
Originally Posted by Opgedronken View Post
Yeah, but in a Miata. Just joined here to follow your build :P.
Sounds like fun :D is there enough space in a miata or do you just have to make enough space?
Sander is offline   Reply With Quote
Old 06-08-2018, 05:15 AM   #180
MadDog_945
Våga Vägra 8V
 
MadDog_945's Avatar
 
Join Date: Apr 2006
Location: Lower Saxony
Default

as long as there is enough flow so the pump isnt sucking air?
MadDog_945 is online now   Reply With Quote
Old 06-08-2018, 01:58 PM   #181
Opgedronken
Newbie
 
Join Date: Jun 2018
Default

Quote:
Originally Posted by Sander View Post
Sounds like fun :D is there enough space in a miata or do you just have to make enough space?
Miatas have massive engine bays, only the height may be an issue :P.
That's why I'm interested to see how low you can get the sump.
On my one I'm going to weld an AN fitting onto the oil pump and relocate the pickup to the back with a hose through the sump.
I'll just put an extra oil drain plug on the front part of the sump.
Opgedronken is offline   Reply With Quote
Old 06-08-2018, 02:41 PM   #182
Mr.Borrie
The Sneaky F*ing Russian
 
Mr.Borrie's Avatar
 
Join Date: Aug 2006
Location: Netherlands
Default

Haha Sander is at it again.. hope i get to see it some time
Mr.Borrie is offline   Reply With Quote
Old 06-08-2018, 05:03 PM   #183
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

Quote:
Originally Posted by MadDog_945 View Post
as long as there is enough flow so the pump isnt sucking air?
That shouldn't be a problem, the tube just connects the forward part of the sump with the rear part. The actual pickup tube that goes to the oil pump will go to the rear sump part.

Quote:
Originally Posted by Opgedronken View Post
Miatas have massive engine bays, only the height may be an issue :P.
That's why I'm interested to see how low you can get the sump.
On my one I'm going to weld an AN fitting onto the oil pump and relocate the pickup to the back with a hose through the sump.
I'll just put an extra oil drain plug on the front part of the sump.
The middle part there on the new oil pan i'm making is about the lowest you can make it. Dry sump or not. In this pic you can see the crankshaft and the windage tray underneath it.



Do you have the engine already? In the Volvo the height of the engine is only an issue at the very front of it. I can imagine it's worse in the miata. It isn't super high, just increadibly long, so if a hood slopes down like in most cars, that's where you'll have space issues. From the gearbox face to the front of the pulley is around 85cm.

Quote:
Originally Posted by Mr.Borrie View Post
Haha Sander is at it again.. hope i get to see it some time
Haha sure that can be arranged, once it's finished I do intend to drive it a lot.
Sander is offline   Reply With Quote
Old 06-08-2018, 07:29 PM   #184
Opgedronken
Newbie
 
Join Date: Jun 2018
Default

I don't have the engine yet, it's on the boat from Japan as we speak :P.
Great to hear the measurement of 85cm is from the trans mounting face to the pulley.
I've seen it mentioned on forums before, but no one mentions from where to where the measurement is.
The m120 has a big part of the bellhousing attached to it so it's a bit different from most other engines.

Where in the netherlands are you located? I'm in Venlo myself.
Opgedronken is offline   Reply With Quote
Old 06-09-2018, 02:30 PM   #185
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

Been working on the subframe and finishing up the front suspension. Painted the new lowered subframe and all the other 960 suspension bits, installed the 960 toe rods and end links on the steering rack and put it all on the car. Also redid most of the underbody protection in the wheel well as it was showing it's age there. Next up I'll properly clean the engine bay and add heat shielding etc where the exhaust goes. Everything is now sort of temporarily together, I'll still replace most rusted ugly bolts with new ones and still have to replace the bushings in the control arms.


















Quote:
Originally Posted by Opgedronken View Post
I don't have the engine yet, it's on the boat from Japan as we speak :P.
Great to hear the measurement of 85cm is from the trans mounting face to the pulley.
I've seen it mentioned on forums before, but no one mentions from where to where the measurement is.
The m120 has a big part of the bellhousing attached to it so it's a bit different from most other engines.

Where in the netherlands are you located? I'm in Venlo myself.
That's true, although on the left cylinder bank it's not so much space from the belhousing. I moved to Germany a few years ago, close to Trier on the border with Luxemburg (about 3 hours from Venlo) but the car is still registered in NL. I'll try to register it here once it's all done and a
Sander is offline   Reply With Quote
Old 06-11-2018, 08:55 AM   #186
Opgedronken
Newbie
 
Join Date: Jun 2018
Default

Damn getting that registered in germany isn't ging to be fun :P.
Opgedronken is offline   Reply With Quote
Old 06-11-2018, 04:31 PM   #187
MadDog_945
Våga Vägra 8V
 
MadDog_945's Avatar
 
Join Date: Apr 2006
Location: Lower Saxony
Default

quite impossible ;) i think he has it registered op de nederlanden, junge
MadDog_945 is online now   Reply With Quote
Old 06-14-2018, 12:08 PM   #188
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

Been spending quite a bit of time on a 1000 little things that still needed doing but are not interesting enough to post here. Although I did make a bit of progress. Decided to get new control arms instead of replacing the bushings in the ones I had, as they were getting a bit crunchy where the bushings are pressed in.













Few pics of how the pan will sit in the car. It'll be a bit higher than in the pictures here when bolted to the engine. The lower suspension cross brace will probably just clear the trans without modification.









Pan almost finished up, testing for leaks. My alu welding isn't the best the world has ever seen, but it'll hold.





Sander is offline   Reply With Quote
Old 06-14-2018, 01:55 PM   #189
arsenix
Board Member
 
Join Date: Feb 2003
Location: Milpitas, CA
Default

Are those the aluminum control arms or the steel?

How worried are you about the rear control arm bushing?

Steady progress
__________________
88' 740 GLE Wagon - B230FT, T5 Trans, MSII-extra, G80, 3" T->T Exhaust
- - > Project Thread < - -
My new project - 1990 740 SE Wagon
arsenix is offline   Reply With Quote
Old 06-14-2018, 03:46 PM   #190
Sander
Good news everyone!
 
Sander's Avatar
 
Join Date: Aug 2006
Location: NL/DE
Default

Quote:
Originally Posted by arsenix View Post
Are those the aluminum control arms or the steel?

How worried are you about the rear control arm bushing?

Steady progress
They are the steel ones, should hold just fine. The rear bushing doesn't bother me, it's brand new. Should hold fine. If it fails, found someone who makes poly bushings for it
Sander is offline   Reply With Quote
Old 06-14-2018, 04:28 PM   #191
arsenix
Board Member
 
Join Date: Feb 2003
Location: Milpitas, CA
Default

In my experience the poly bushings for that type of joint work like poop. I installed poly rear control arm bushings in a Golf a few years ago (similar type of control arm). They were destroyed in a few months. I was thinking about retrofitting a VW TT solid control arm bushing into there, or Moog makes a "spherical bushing" for these applications. Every other manufacturer other than Volvo uses a 60mm OD bushing though... Volvo is 70mm.
arsenix is offline   Reply With Quote
Old 06-15-2018, 01:18 PM   #192
Opgedronken
Newbie
 
Join Date: Jun 2018
Default

The sump is coming along great!
Are you going to mill all the welds on the bolt holes flat?
Opgedronken is offline   Reply With Quote
Old 06-16-2018, 12:12 AM   #193
Jeh
Wants a V12
 
Jeh's Avatar
 
Join Date: Dec 2006
Location: on a crappy road...
Default

Wow. It always amazes me to see the amount of work going into a project like this. Just awesome.
Jeh is offline   Reply With Quote
Old 06-16-2018, 05:02 AM   #194
nordmaschine
forced instruction
 
nordmaschine's Avatar
 
Join Date: Feb 2012
Location: The Balkans, BiH
Default

Quote:
Originally Posted by arsenix View Post
In my experience the poly bushings for that type of joint work like poop. I installed poly rear control arm bushings in a Golf a few years ago (similar type of control arm). They were destroyed in a few months. I was thinking about retrofitting a VW TT solid control arm bushing into there, or Moog makes a "spherical bushing" for these applications. Every other manufacturer other than Volvo uses a 60mm OD bushing though... Volvo is 70mm.
5mm thick sleeve could take care of that. I always go with TT bushings on VW's, they rock...
__________________
Jetronic is romantic.
- '94 965 - D̶2̶4̶T̶I̶C̶, then M̶5̶0̶B̶2̶5̶ now OM606.962.
- '90 744 turbo 16 valve LPG - B204GT/M90 - trophy w̶i̶f̶e̶ car.
- '89 764 B280F - Daily barge.
- Various 740's, 940's, 960's and a couple of 760's.
Quote:
Originally Posted by Kjets On a Plane View Post
Whiteblocks
Quote:
Originally Posted by AdmiralSenn View Post
I think I might be too stupid to own a car.
nordmaschine is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 03:50 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.