Squirterizational mod RENTAL KIT for INCREASED PERFORMANCE - Page 6

240driver · 12-05-2008, 10:42 PM

Why thank you sir! Very helpful post.

supraboy · 12-29-2008, 06:12 PM

Hey john, whats the center 2 center distance on the bushing fixture?

Delfosse · 12-29-2008, 07:52 PM

It's my turn for the kit!!!!!!!

John is sending me a set of squirters today!

This is the last thing I need to do before putting my motor back together!

John V, outside agitator · 12-29-2008, 07:55 PM

Quote:

Originally Posted by supraboy

Hey john, whats the center 2 center distance on the bushing fixture?

I dunno I don't have the kit here. I think MrBill has it.
I recall its about meeeeehhhhhh that much.

supraboy · 12-29-2008, 08:25 PM

lol, ok, thanks

Delfosse · 12-30-2008, 06:19 PM

Who has the kit?

SteveMD · 12-30-2008, 08:12 PM

Quote:

Originally Posted by Delfosse

Who has the kit?

I haz it. I need to rent a 3/4 inch drill as the spot face cutter shank is too large for my 1/2 inch drill chucks. I hope to do that tomorrow at the earliest or Friday at the latest.

John V, outside agitator · 12-31-2008, 04:58 PM

Quote:

Originally Posted by MrSteve

I haz it. I need to rent a 3/4 inch drill as the spot face cutter shank is too large for my 1/2 inch drill chucks. I hope to do that tomorrow at the earliest or Friday at the latest.

Damn, I'll see about turning the shank down a bit if it ever comes back to Sleezattle.

Delfosse · 12-31-2008, 07:38 PM

Quote:

Originally Posted by MrSteve

I haz it. I need to rent a 3/4 inch drill as the spot face cutter shank is too large for my 1/2 inch drill chucks. I hope to do that tomorrow at the earliest or Friday at the latest.

When your done contact me then send it to me! Then, I'll send it back to john so he can check it for maintenance!

Mueller · 12-31-2008, 07:50 PM

Quote:

Originally Posted by John V, outside agitator

Damn, I'll see about turning the shank down a bit if it ever comes back to Sleezattle.

worked fine in my cheap cordless drill from what I remember....

SteveMD · 01-01-2009, 07:22 PM

Whoops! False alarm.

It turns out both my drills are 3/8 chuck. I'm hoping to borrow a 1/2 incher from a TB member Saturday.

John V, outside agitator · 01-01-2009, 08:08 PM

Quote:

Originally Posted by MrSteve

Whoops! False alarm.

It turns out both my drills are 3/8 chuck. I'm hoping to borrow a 1/2 incher from a TB member Saturday.

Geeeeeet aaaaawn eeeeeet!

Lord Tentacle · 01-08-2009, 09:34 AM

any news when a kit will make it to aus?

SteveMD · 01-09-2009, 11:26 AM

I moved on to the next to last step, enlarging the holes for tapping only to find the larger of the 2 long drill bits in the kit is bent and the shank chewed up. Going drill bit shopping this weekend.

pyropete125 · 01-09-2009, 06:24 PM

where do you get the squirters? p/n? price?

thanks,
pete

John V, outside agitator · 01-09-2009, 07:26 PM

Quote:

Originally Posted by pyropete125

where do you get the squirters? p/n? price?

thanks,
pete

Most guys get them from me since I'm such an all round swell fellah and invented the kit and fought with some so called moderator to get this Loaner Kit idea made into a sticky.

I've been selling them for 15.50 each.

John V, outside agitator · 01-09-2009, 07:26 PM

Quote:

Originally Posted by MrSteve

I moved on to the next to last step, enlarging the holes for tapping only to find the larger of the 2 long drill bits in the kit is bent and the shank chewed up. Going drill bit shopping this weekend.

It's 7mm, OK.

pyropete125 · 01-09-2009, 07:59 PM

do they have the ball and spring so at lower oil pressures they dont squirt? any idea on the psi they start to work?

think they would work on a ford 2.3?

so basicly i just need to call you up to order them

?

thanks!

pete

John V, outside agitator · 01-10-2009, 02:43 PM

[QUOTE=pyropete125;2218306]

Quote:

do they have the ball and spring so at lower oil pressures they dont squirt? any idea on the psi they start to work?

Yep

Quote:

think they would work on a ford 2.3?

Pretty damn sure, if not these then maybe Mitsubishi 4G62 (which I also have)

Quote:

so basicly i just need to call you up to order them

?

Sure.

Quote:

thanks!

No problem

SteveMD · 01-12-2009, 09:42 AM

Quote:

Originally Posted by John V, outside agitator

It's 7mm, OK.

Gonna have to order it from McMaster Carr unless I find a cheaper source.

John V, outside agitator · 01-12-2009, 03:48 PM

Quote:

Originally Posted by MrSteve

Gonna have to order it from McMaster Carr unless I find a cheaper source.

I think I can pick up another for cheap and send it, but somebody is going to have to confess they bent the things.

Hey folks, this stuff doesn't cost a lot, so if you FAWK UP A DRILL say so, that's what the deposit is for so I can deduct 4-6 bucks and when it goes to the next guy HE'S NOT STUCK and I don't have to go to the fawkin post office a second time on my own time.

Come on this is done on the honor system boys, be straight with the rest of us.

meeki007 · 01-26-2009, 05:31 AM

Hey every on i know I'm to new to this community to get my hands on that kit for a while so I'm going to make 1 myself.

Right now I Am just taking my rebuild slow and will not be ready to do the Squirterizational mod for another 2 weeks on my time frame so i fig id make a 2nd kit and start shipping it out to others as well.

1) If i do this i will expect you all to be buying your squirter bolts from John V. As he has taken the time to setup this mod and figure out all the kinks.

2) The kit will be on a 2 week loan. From the date i ship to the date its return postmark is on the box. this should give you about 9-10 days if your in the U.S and 7-8 days if it has to go overseas. The Idea for this is that you don't ask for the kit unless your engine block is on the stand prepped and ready.

3) Deposit - I am looking at $75 US

4) 1 little change to the rules. Instead of shipping to the next dude inline it will be coming back to me because of issues with the first kit being damaged and no one owning up to it. This will allow me to inspect bits and sharpen them if need be or replace if broke. If only bits are broke you'll only be out a few bucks. You brake or bend the fixture/jig (it does both depending on how much you tighten it) well could cost ya 1/2 your deposit.

I want to have a very similar kit as it has been proven by John V. I need the kit owners help or John's help. Or it could take me longer to fig this out.

First if you could get out a pair of digital calipers or other accurate measuring device and tell me the distance from the center of the M8 bolt and the center of the shim as shown in the picture below.Be accurate!

Second I need the diameter or preferably the size of the spot face cutter. See pic 2 below. If you don't have this and john if you know or have a squirter to measure that would be great.

MikeHardy · 01-26-2009, 05:50 AM

Quote:

Originally Posted by John V, outside agitator

Most guys get them from me since I'm such an all round swell fellah and invented the kit and fought with some so called moderator to get this Loaner Kit idea made into a sticky.

Fought with? pretty sure i just read the thread and made it sticky. no fighting involved

John V, outside agitator · 01-26-2009, 12:48 PM

Quote:

Originally Posted by ravennexus

Fought with? pretty sure i just read the thread and made it sticky. no fighting involved

The first time it was posted one of the countless people around here who are moderators was either unable to read the extra large, bold, italicized and underlined words "Loaner kit" or they were unable to overcome their personal animus which makes then so angry they are unable to read, and whoever it was moved the thread to the FOR SALE SECTION. Which was really really either stupid or vindictive, or both.
Eventually another moderator undid the other moderators work and now we have this nice free service available.

740tankDriver · 02-10-2009, 01:05 AM

where is the...one...kit now?

01-26-2009, 05:31 AM	#147
meeki007 Board Member Join Date: Jan 2009 Location: Oregon	Id like to make a kit Hey every on i know I'm to new to this community to get my hands on that kit for a while so I'm going to make 1 myself. Right now I Am just taking my rebuild slow and will not be ready to do the Squirterizational mod for another 2 weeks on my time frame so i fig id make a 2nd kit and start shipping it out to others as well. 1) If i do this i will expect you all to be buying your squirter bolts from John V. As he has taken the time to setup this mod and figure out all the kinks. 2) The kit will be on a 2 week loan. From the date i ship to the date its return postmark is on the box. this should give you about 9-10 days if your in the U.S and 7-8 days if it has to go overseas. The Idea for this is that you don't ask for the kit unless your engine block is on the stand prepped and ready. 3) Deposit - I am looking at $75 US 4) 1 little change to the rules. Instead of shipping to the next dude inline it will be coming back to me because of issues with the first kit being damaged and no one owning up to it. This will allow me to inspect bits and sharpen them if need be or replace if broke. If only bits are broke you'll only be out a few bucks. You brake or bend the fixture/jig (it does both depending on how much you tighten it) well could cost ya 1/2 your deposit. I want to have a very similar kit as it has been proven by John V. I need the kit owners help or John's help. Or it could take me longer to fig this out. First if you could get out a pair of digital calipers or other accurate measuring device and tell me the distance from the center of the M8 bolt and the center of the shim as shown in the picture below.Be accurate! Second I need the diameter or preferably the size of the spot face cutter. See pic 2 below. If you don't have this and john if you know or have a squirter to measure that would be great.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-05-2008, 10:42 PM	#126
240driver Board Member Join Date: Oct 2008 Location: WV	Why thank you sir! Very helpful post.

12-29-2008, 06:12 PM	#127
supraboy betting on a long-shot. Join Date: Jun 2007 Location: TEXAS	Hey john, whats the center 2 center distance on the bushing fixture?

12-29-2008, 07:52 PM	#128
Delfosse Board Member Join Date: May 2006	It's my turn for the kit!!!!!!! John is sending me a set of squirters today! This is the last thing I need to do before putting my motor back together!

12-29-2008, 08:25 PM	#130
supraboy betting on a long-shot. Join Date: Jun 2007 Location: TEXAS	lol, ok, thanks

12-30-2008, 06:19 PM	#131
Delfosse Board Member Join Date: May 2006	Who has the kit?

01-01-2009, 07:22 PM	#136
SteveMD Membro Join Date: Feb 2004 Location: Stop paddling, I hear banjos.	Whoops! False alarm. It turns out both my drills are 3/8 chuck. I'm hoping to borrow a 1/2 incher from a TB member Saturday.

01-09-2009, 11:26 AM	#139
SteveMD Membro Join Date: Feb 2004 Location: Stop paddling, I hear banjos.	I moved on to the next to last step, enlarging the holes for tapping only to find the larger of the 2 long drill bits in the kit is bent and the shank chewed up. Going drill bit shopping this weekend.

01-09-2009, 06:24 PM	#140
pyropete125 Board Member Join Date: Mar 2007 Location: west haven, CT	where do you get the squirters? p/n? price? thanks, pete

01-09-2009, 07:59 PM	#143
pyropete125 Board Member Join Date: Mar 2007 Location: west haven, CT	do they have the ball and spring so at lower oil pressures they dont squirt? any idea on the psi they start to work? think they would work on a ford 2.3? so basicly i just need to call you up to order them ? thanks! pete

02-10-2009, 01:05 AM	#150
740tankDriver Post-Hypnotic Sigma Join Date: Aug 2006 Location: Under your nose.	where is the...one...kit now?