home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > projects & restorations

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 02-05-2018, 04:28 PM   #24
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Oh hey so this happened this weekend



Scrutineer really liked the cage.

Have not updated this - mostly been busy with work the past 3-4 months saving up money for rally season this year.

I quit my job at the Porsche shop I was at due to an ownership change.

The rally car has lived in my friends enclosed trailer the past few months.

Since moving on from the Porsche shop, 3 weeks ago I pushed the E36 project that belongs to my friend into the garage to complete it. Once its done, the rally car goes in the garage for paint and the rest of the work.

The e36 - 1994 325is. I sold him this car 9 years ago after buying it off my friends dad [he got it when we were in middle school, and it was always the car we would try and sneak out and joyride when that friend got his license], we had Evil Genius cage it 8 years ago, I stripped the rest of the car since as well as pulling and reinstalling the engine with all the work we have done to it.

The past 3 weeks I have spent planning the completion of the project for him - installing the suspension goodies, new brakes and the biggest project - a full rewire of the entire car. We hucked the old harness years ago. I found an engine harness at the junkyard from another 94 325is and started with that. I'm almost at the point where I can pull the harness out and can start adding protective sheathing to the looms.




What's done to the e36

M50....new gaskets and seals all around...VANOS delete, ARP head stud conversion, VAC racing timing chain (new guides too), VAC racing oil pump, VAC pan baffle, VAC oil filter housing with a large Setrab oil cooler and -10 Peterson inline oil filter, VAC underdrive pulleys, Racing Dynamics header, catless mid pipe, B&B rear exhaust, Euro 3.5'' MAF conversion, custom DME tune, ACS delete, solid engine mounts. Added a fuel pump on the drivers side to feed the passenger pump pickup to prevent starvation below 1/2 tank.

Getrag 5 speed...UUC aluminum flywheel, E34 M5 clutch, HD guibo, 3.91 LSD, fully reinforced rear subframe, Bimmerworld solid race shifter, solid trans mount, braided slave cylinder hose

E46 330i front brakes (325mm), E46 325i rear brakes (slightly bigger and vented discs), slotted discs all around, Porterfield R4 pads, custom brake duct setup, braided steel hoses all around

Adjustable 30mm front/25mm rear sway bars, Turner adjustable endlinks all around, H&R front coilovers, Ground Control camber plates, H&R rear race springs and Bilsteins in the back, adjustable rear lower control arms, upgraded rear shock mounts, front and rear shock tower bracing.

I think we are going to mostly be doing Lucky Dog Racing League with this car. Because of the modifications, it does not really fit an SCCA/NASA class that it can be legal or competitive in. I think it will kick ass.
__________________
- Patrick
83 244ti - road race
83 244ti - rally
73 1800es - resto
08 c30 T5 6spd - daily
97 dakota 5.2 4x4 single cab short bed - apocalypse mobile

Last edited by pat244ti; 02-05-2018 at 04:42 PM..
pat244ti is offline   Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 12:41 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.