home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > projects & restorations

Reply
 
Thread Tools Display Modes
Old 02-05-2018, 04:28 PM   #101
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Oh hey so this happened this weekend



Scrutineer really liked the cage.

Have not updated this - mostly been busy with work the past 3-4 months saving up money for rally season this year.

I quit my job at the Porsche shop I was at due to an ownership change.

The rally car has lived in my friends enclosed trailer the past few months.

Since moving on from the Porsche shop, 3 weeks ago I pushed the E36 project that belongs to my friend into the garage to complete it. Once its done, the rally car goes in the garage for paint and the rest of the work.

The e36 - 1994 325is. I sold him this car 9 years ago after buying it off my friends dad [he got it when we were in middle school, and it was always the car we would try and sneak out and joyride when that friend got his license], we had Evil Genius cage it 8 years ago, I stripped the rest of the car since as well as pulling and reinstalling the engine with all the work we have done to it.

The past 3 weeks I have spent planning the completion of the project for him - installing the suspension goodies, new brakes and the biggest project - a full rewire of the entire car. We hucked the old harness years ago. I found an engine harness at the junkyard from another 94 325is and started with that. I'm almost at the point where I can pull the harness out and can start adding protective sheathing to the looms.




What's done to the e36

M50....new gaskets and seals all around...VANOS delete, ARP head stud conversion, VAC racing timing chain (new guides too), VAC racing oil pump, VAC pan baffle, VAC oil filter housing with a large Setrab oil cooler and -10 Peterson inline oil filter, VAC underdrive pulleys, Racing Dynamics header, catless mid pipe, B&B rear exhaust, Euro 3.5'' MAF conversion, custom DME tune, ACS delete, solid engine mounts. Added a fuel pump on the drivers side to feed the passenger pump pickup to prevent starvation below 1/2 tank.

Getrag 5 speed...UUC aluminum flywheel, E34 M5 clutch, HD guibo, 3.91 LSD, fully reinforced rear subframe, Bimmerworld solid race shifter, solid trans mount, braided slave cylinder hose

E46 330i front brakes (325mm), E46 325i rear brakes (slightly bigger and vented discs), slotted discs all around, Porterfield R4 pads, custom brake duct setup, braided steel hoses all around

Adjustable 30mm front/25mm rear sway bars, Turner adjustable endlinks all around, H&R front coilovers, Ground Control camber plates, H&R rear race springs and Bilsteins in the back, adjustable rear lower control arms, upgraded rear shock mounts, front and rear shock tower bracing.

I think we are going to mostly be doing Lucky Dog Racing League with this car. Because of the modifications, it does not really fit an SCCA/NASA class that it can be legal or competitive in. I think it will kick ass.
__________________
- Patrick
83 244ti - road race
83 244ti - rally
73 1800es - resto
08 c30 T5 6spd - daily
97 dakota 5.2 4x4 single cab short bed - apocalypse mobile

Last edited by pat244ti; 02-05-2018 at 04:42 PM..
pat244ti is offline   Reply With Quote
Old 02-06-2018, 10:38 AM   #102
tjanson
Board Member
 
tjanson's Avatar
 
Join Date: Apr 2004
Location: Underhill, VT
Default

Nice move on the 5x114 bolt pattern. Enough material on the hubs and flanges just to add the new pattern? Running spacers I assume? Subaru M12 studs or Volvo 1/2"? or beefcake M14?
__________________
1978 242 GT; B230F LH 2.2, M47
1993 245 DL; LH2.4, M47
tjanson is offline   Reply With Quote
Old 02-06-2018, 01:25 PM   #103
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Quote:
Originally Posted by tjanson View Post
Nice move on the 5x114 bolt pattern. Enough material on the hubs and flanges just to add the new pattern? Running spacers I assume? Subaru M12 studs or Volvo 1/2"? or beefcake M14?
M12 studs.

No spacers actually - the Methods I found (evo fitment, stocked up and bought 10 from a guy who was selling them for like $120/pop) are ET 15 which is perfect. Had to have some 2mm hubrings made and that was it

Plenty of material between the two sets of holes I think.

Last edited by pat244ti; 02-06-2018 at 01:48 PM..
pat244ti is offline   Reply With Quote
Old 02-08-2018, 01:42 PM   #104
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

Quote:
Originally Posted by tjanson View Post
Nice move on the 5x114 bolt pattern. Enough material on the hubs and flanges just to add the new pattern? Running spacers I assume? Subaru M12 studs or Volvo 1/2"? or beefcake M14?
It really is a good step up. I can buy used Methods all day long for $50-100. We used to go through at least 1 OEM volvo wheel an event. We haven't gone through a wheel in 8 races since switching to the Method VT-Spec wheels.

We use the higher offset wheels and spacers currently, but we can run the 15mm offset wheels by just removing the spacers
__________________
Cult Person. Pissing in your Kool-Aid.
culberro is offline   Reply With Quote
Old 02-12-2018, 04:37 PM   #105
tjanson
Board Member
 
tjanson's Avatar
 
Join Date: Apr 2004
Location: Underhill, VT
Default

So which cars are the +15mm offset meant for? From what i'm seeing Subarus are +50mm and Mitsubishis are 30-50mm. Is it just for being hella flush?
tjanson is offline   Reply With Quote
Old 02-12-2018, 10:18 PM   #106
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

Quote:
Originally Posted by tjanson View Post
So which cars are the +15mm offset meant for? From what i'm seeing Subarus are +50mm and Mitsubishis are 30-50mm. Is it just for being hella flush?
https://www.methodracewheels.com/col...-rally-vt-spec
culberro is offline   Reply With Quote
Old 02-12-2018, 10:58 PM   #107
tjanson
Board Member
 
tjanson's Avatar
 
Join Date: Apr 2004
Location: Underhill, VT
Default

Yeah, I had seen that. The 501 wheel with +48 offset also says it's "ideal" for Subarus and Mitsubishi's and clears the same brakes...so I am wondering what the reasoning is behind the 15 offset. Just increase track width?
tjanson is offline   Reply With Quote
Old 02-13-2018, 01:47 AM   #108
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

I think is the "wide body STI" vs standard Impreza fitment.
culberro is offline   Reply With Quote
Old 02-13-2018, 03:27 AM   #109
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

The guy I bought them from that had a stack of 100 of them got them for an Evo he was putting together. He wanted 30 or something and had to buy 100 from Method to get a good deal.

I don't know if Karl [Buchka] is reading this, but he picked up the wheels for me from the guys house and has a funny story about it.
pat244ti is offline   Reply With Quote
Old 02-13-2018, 01:50 PM   #110
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

Was his name Andrew by chance?
culberro is offline   Reply With Quote
Old 02-13-2018, 04:36 PM   #111
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Quote:
Originally Posted by culberro View Post
Was his name Andrew by chance?
Bagio
pat244ti is offline   Reply With Quote
Old 09-13-2018, 03:02 PM   #112
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Yeah I am still working on this



Engine bay is pretty much all together. Cranked it over the other night and got a grumble out of it, but did not go much further because of a fuel leak that I need to rectify, plus no exhaust [plus neighbors at 11 pm]

I still need to wrap a bunch of the wiring in the engine bay too now that I know it all works.



Dash is all together. I pulled it back out though because I need to find a way to get the steering column a tad more centered as well as rewiring a few things, again.



Picked up some stuff from Mr Triangles himself a few weeks ago that are going on the car when I swap the new rear end [with 4.56 and Spartan locker!] in once I put some miles on the car with the stock diff [dont feel like driving around to break in the engine/drivetrain with a locked diff on pavement]



My friend Gary is great with fabricating plastic bits, and we made these nice underbody protection panels out of thick starboard [think kitchen cutting boards]



I gave Gary a couple of stock door panels and he cut some ABS sheets for me. I still need to fasten them to the door and a few other things [adding map pockets, a grab handle, etc]



Gary had a scrap piece of lexan he gave me, which I turned into an adjustable spoiler



I was hoping to get the car ready for Tour De Forest next month but it's not going to happen. I think I could still do it, there's just things to contribute to my anxiety [credit card debt, lack of proper registration to drive it on the road which is kind of neccessary, lack of testing, borrowing a truck/trailer] I dont want on my mind the first event.

I am working 65 hour weeks from now until April. Plan is to get the car ready to the point where I am happy with it, save up a buttload of money, get myself a new truck and trailer [overdue] and run the first two events of the ARA schedule next year on the west coast. If all goes well I am going to try the east coast swing of events and go for running national points.
pat244ti is offline   Reply With Quote
Old 09-14-2018, 04:32 PM   #113
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

That wang is huuuuuuuuge!

Coming up to Tour de Forest with Al? I'll be servicing for the Clarks. Should be a good time!
culberro is offline   Reply With Quote
Old 09-15-2018, 11:02 AM   #114
pat244ti
Moderator
 
pat244ti's Avatar
 
Join Date: Dec 2002
Location: Santa Cruz CA
Default

Quote:
Originally Posted by culberro View Post
That wang is huuuuuuuuge!

Coming up to Tour de Forest with Al? I'll be servicing for the Clarks. Should be a good time!
It's about the same height as one of those late model spoilers....so yeah it's not small

I'm making plans to be up there for TDF, I'll be helping Al out for sure if he makes it up. If not my girlfriend and I will be volunteering.

So, speaking of my girlfriend - she wrangled together something amazing yesterday related to the rally car that I will be announcing soon
pat244ti is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 07:40 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.