home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > performance & modifications > aftermarket engine management

Reply
 
Thread Tools Display Modes
Old 08-16-2017, 07:23 AM   #2126
Brickinthewall
Newbie
 
Join Date: May 2017
Location: Sweden
Default

Thanks
I will try that on my way home from work this afternoon...
The funny thin is that I tried to upload several different 219 bins(supposed to be)
One of them showed 30 degrees ignition at idle rpms and the other 15 degrees.
After upload went through theres no respond in the sound of the engine at idle.
When I a couple of years ago used a aftermarket system and did similar things the engine noise changed with the ignition retardation changing of the parameters.
But I will try once again on my way home...
I have a setup were 1C50(I believe).. 3... 5... 7... is in different folders, on top of that there is 2 other folders(edit and calculated that I ve created).
I found (I believe) that 2 hexadresses backwards I can adjust the scaling of the "editable map" ("calculated map" rev range is changed in tunerpro and not linked).

Dont know if it is workin in reality or if I just rearrange the graphical view...
In the fuel maps you will find a similar pattern of 2 adresses backwards were a 1*16 table exist. And by changing bytes in that table the RPM scale gets extended towards higher RPMs... Done the same in the load table 1-128 to 4-244 and then I didnt reach the end of load map while revving at standstill... Since that was working graphically I continued in the same manner in the other tables...

I have no clue but it is fun says the idiot(me)
Brickinthewall is offline   Reply With Quote
Old 11-07-2017, 12:58 PM   #2127
Raimis760t
Board Member
 
Join Date: Apr 2016
Location: Lithuania
Default

hello, can someone give me advice. My 740 setup is B230F + T, 13T 7cm, 350cc injectors, 016amm, 3" dp/exhaust, 984lh /148ezk, with 967bin. Dyno'ed at 0.85bar / 197hp/335nm
Question: That value set to Torq signal to ezk adjuster for my NA + T ??
__________________
89" VOLVO 760, B230FT, 16T, big IC, 3" dp and exhaust, 044 fuel pump, custom manifold Up pipe, KL-Racing T2 Cam and Cam gear, DET3 piggy, FPR, Bov, custom intake from turbo to manifold, hidraulic hand brake, welded diff, stripped interior, and.... 268HP 382NM
Raimis760t is offline   Reply With Quote
Old 01-11-2018, 11:47 AM   #2128
esmth
dirty swede
 
esmth's Avatar
 
Join Date: Jul 2016
Location: Massachusetts
Default Ebay eprom programmers

I want to be able to create a chip so I don't need the ostrich always in my passenger footwell. and I can tweak ezk tables with my edited fuel tables.

What cheap eprom programmers do you use? I'm looking at this one but I'm worried about the driver situation.

https://www.ebay.com/itm/NEW-KEE-Wil...0AAOSwdU1W8qF4

I have a computer with a parallel port and I'd like to use that
__________________
1991 244 +T LH2.4 m46 281k miles with B cam & STS cam gear adv 4*, 954 fuel & 207 ezk tuned with Ostrich, 350cc EV6 white injectors, 2.5" exhaust w/ magnaflow straight-through, SLC free wideband
esmth is offline   Reply With Quote
Old 01-12-2018, 05:30 PM   #2129
Sjeng
Newbie
 
Join Date: Sep 2017
Default

https://www.aliexpress.com/item/V6-0...ceBeautifyAB=0

USB port(you don't have that?), very straightforward operation.
Sjeng is offline   Reply With Quote
Old 01-13-2018, 04:58 PM   #2130
SoapNh20
Newbie
 
Join Date: Sep 2017
Default

I need a little help. 1991 940 turbo do88 silicone hoses, 15g turbo V70r injectors(not installed yet) lh 2.4 ecu#563. I just got ostrich 2.0 and tuner pro. I'm having trouble finding a bin to match my ecu. Ive tried the bin from ipdown.net (great site) and its not working(maybe its me). when I unzip the file it isn't a .bin file so it wont work with the .xdf it comes with. Both .bin files for a #560 ecu from tunerpro.net and ipdown.net were able to start the car but it could barely idle.

Is there another source for .bin/.xdf files?
Is there another ecu .bin that could start the car? I tried a bunch and the fuel pump wouldn't prime.
Could I get another ecu and .bin file to match that ecu? I found 93 940T at the upull. Not sure if another ecu would be compatible with my car. Still in the process of searching and reading. I know this is where to find the gurus. thanks in advance
SoapNh20 is offline   Reply With Quote
Old 01-15-2018, 05:03 AM   #2131
mrjaybeeze
Board Member
 
Join Date: Feb 2008
Location: norway
Default

Quote:
Originally Posted by SoapNh20 View Post
I need a little help. 1991 940 turbo do88 silicone hoses, 15g turbo V70r injectors(not installed yet) lh 2.4 ecu#563. I just got ostrich 2.0 and tuner pro. I'm having trouble finding a bin to match my ecu. Ive tried the bin from ipdown.net (great site) and its not working(maybe its me). when I unzip the file it isn't a .bin file so it wont work with the .xdf it comes with. Both .bin files for a #560 ecu from tunerpro.net and ipdown.net were able to start the car but it could barely idle.

Is there another source for .bin/.xdf files?
Is there another ecu .bin that could start the car? I tried a bunch and the fuel pump wouldn't prime.
Could I get another ecu and .bin file to match that ecu? I found 93 940T at the upull. Not sure if another ecu would be compatible with my car. Still in the process of searching and reading. I know this is where to find the gurus. thanks in advance


Hi

Please remember that this ECU is first generation and amongst the oldest out there.

The XDF and BIN file should work OK on your ECU, just remember to UNZIP the Bin file before attempting to use it.

YS
Jaybee
__________________
ipdown.net/jetronic.info/tiki-index.php
Site open in "lame mode"
If you have some issues
just send me a message
mrjaybeeze is offline   Reply With Quote
Old 01-15-2018, 11:45 PM   #2132
SoapNh20
Newbie
 
Join Date: Sep 2017
Default

Quote:
Originally Posted by mrjaybeeze View Post
Hi

Please remember that this ECU is first generation and amongst the oldest out there.

The XDF and BIN file should work OK on your ECU, just remember to UNZIP the Bin file before attempting to use it.

YS
Jaybee
Unzipping the .bin file is where I run into the issue. The file did not end in .zip, it came up as a text document. It would not unzip. The rest of the files I tried ended in .zip, unzipped no issue and were able to be viewed and loaded to ostrich from tuner pro. I will try again and again.

Would there be any gain in purchasing a newer ECU? Thanks for your help
SoapNh20 is offline   Reply With Quote
Old 01-16-2018, 04:12 AM   #2133
mrjaybeeze
Board Member
 
Join Date: Feb 2008
Location: norway
Default hi

That seems weird...
I do use 7zip to open it and no issues whatsoever since 7z does not care what file extension it has.
You could try that or mail me at my username @hotmail.com and I can send you the unzipped version.

YS
Jaybee
mrjaybeeze is offline   Reply With Quote
Old 01-16-2018, 06:49 PM   #2134
esmth
dirty swede
 
esmth's Avatar
 
Join Date: Jul 2016
Location: Massachusetts
Default

Quote:
Originally Posted by Sjeng View Post
https://www.aliexpress.com/item/V6-0...ceBeautifyAB=0

USB port(you don't have that?), very straightforward operation.
i'm all for aliexpress but 1 month to 40 days shipping estimate is horrid. I actually ordered the one i linked to on ebay. i'll update if it ends up not working
esmth is offline   Reply With Quote
Old 01-17-2018, 12:36 AM   #2135
SoapNh20
Newbie
 
Join Date: Sep 2017
Default

Quote:
Originally Posted by mrjaybeeze View Post
That seems weird...
I do use 7zip to open it and no issues whatsoever since 7z does not care what file extension it has.
You could try that or mail me at my username @hotmail.com and I can send you the unzipped version.

YS
Jaybee
7zip got it working. I was using winzip and it was not working for that particular bin for whatever reason. Thanks

Last edited by SoapNh20; Yesterday at 12:55 AM..
SoapNh20 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 01:13 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.