home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Mechanical > performance & modifications

Reply
 
Thread Tools Display Modes
Old 10-12-2018, 11:31 PM   #1
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default CD009 to 244 build thread

I am a madman.


the m47 and cd009 pre bellhousing and input shaft cut.


after cut just the cd009


Working on a relocation deal so i can get the shifter to roughly come out here:


Cardboard debauchery, plate on top is 6.5" x 6.5" square, for now, with the bracket on the right side of the CD being spaced out an inch to clear the top of the trans :


Gotta shorten and weld these two pieces together next and figure out how to cut and get this piece of the original shift turret to connect.




Updates will happen at some point along the process

UPDATE! 11/2/18

test fit done sans clutch and pressure plate, Deeworks CD009 to redblock adapter, working on a shifter setup for the stock location. just a little bit of banging on the trans tunnel for clearance otherwise fits like a glove! Will update more tomorrow on the cross-member modification and clearance for the tunnel.


[IMG]45241083-198587721059719-6428737929467658240-n 45256699-747467898932767-166529939493879808-n 45328001-358298011574388-7621189209260294144-n[/IMG]

Last edited by AndrewTheHobbit; 11-02-2018 at 09:59 PM.. Reason: more pics
AndrewTheHobbit is offline   Reply With Quote
Old 10-14-2018, 04:25 PM   #2
GreatDaneShane
Board Member
 
GreatDaneShane's Avatar
 
Join Date: Jul 2007
Location: Houston, Texas
Default

Looking good!
GreatDaneShane is offline   Reply With Quote
Old 10-14-2018, 08:24 PM   #3
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default

Quote:
Originally Posted by GreatDaneShane View Post
Looking good!
Thanks! currently working on a way to make the old m47 shift linkage work with the CD, have to wait on my deeworks adapter to see how much clearance I'm gonna have on the rear of the trans.
AndrewTheHobbit is offline   Reply With Quote
Old 10-15-2018, 01:19 AM   #4
t8fanning
8v are still cool, right?
 
t8fanning's Avatar
 
Join Date: Oct 2010
Location: Cedar Hills, UT
Default

I'll be interested to see how it fits in the tunnel.
__________________
1982 242 Turbo.
t8fanning is offline   Reply With Quote
Old 10-15-2018, 08:37 AM   #5
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Looks like it's going behind an LS? I've got the same thing going on with my 240.

What motor mounts/oil pan are you using? The trans position you have there looks pretty close to mine. I'm using those STS mounts, but then I moved things forward about 1 1/4" just to make clearance issues on various things (bellhousing, steering column) go away.
__________________
'63 PV Rat Rod
'93 245 16VT Classic #1141
JohnMc is offline   Reply With Quote
Old 10-15-2018, 08:52 AM   #6
poulrais
Board Member
 
poulrais's Avatar
 
Join Date: Sep 2006
Location: Quebec, CAN
Default

Damn that thing is so shiny! Did you buy it brand new?
__________________




1990, Volvo 740 16v +T
1991, Volvo 745T 16V - crushed
build thread: http://forums.turbobricks.com/showthread.php?t=249553
poulrais is online now   Reply With Quote
Old 10-15-2018, 09:04 AM   #7
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

Brand new ones really aren't all that bad: https://www.z1motorsports.com/manual...on-p-3342.html
Less than a worn out T56.
JohnMc is offline   Reply With Quote
Old 10-15-2018, 12:33 PM   #8
culberro
Ronald Culberbone III
 
culberro's Avatar
 
Join Date: Feb 2010
Location: Portland, OR
Default

Quote:
Originally Posted by JohnMc View Post
Brand new ones really aren't all that bad: https://www.z1motorsports.com/manual...on-p-3342.html
Less than a worn out T56.
That's the price of a new T5-Z! That's a smoking deal for those that want a more "refined" transmission that will handle more torque than a t5.
__________________
Cult Person. Pissing in your Kool-Aid.
culberro is offline   Reply With Quote
Old 10-15-2018, 02:39 PM   #9
dl242gt
Can play the blues
 
dl242gt's Avatar
 
Join Date: Jun 2002
Location: S NJ, a suburb of Phila.
Default

That is the same price as a rebuilt M47 exchange from Volvo last time I checked.
dl242gt is online now   Reply With Quote
Old 10-15-2018, 02:51 PM   #10
Tfrasca
Board Member
 
Tfrasca's Avatar
 
Join Date: Apr 2015
Location: Aptos, CA
Default

Quote:
Originally Posted by culberro View Post
That's the price of a new T5-Z! That's a smoking deal for those that want a more "refined" transmission that will handle more torque than a t5.
I just paid 2k for a new T5z a few months ago. This seems like a way better option.

However, I'm really curious about noises from the CD009. At first everyone said they were smooth and quiet and shift well, but I've been looking at other forums and Z people seem to think they're loud.

I know of one person who has a single mass flywheel on a Vr6 with this trans, and says it does the T5 neutral rattle thing really badly.

Curious to actually drive one of these.
Tfrasca is offline   Reply With Quote
Old 10-15-2018, 04:22 PM   #11
poulrais
Board Member
 
poulrais's Avatar
 
Join Date: Sep 2006
Location: Quebec, CAN
Default

Quote:
Originally Posted by Tfrasca View Post
I just paid 2k for a new T5z a few months ago. This seems like a way better option.

However, I'm really curious about noises from the CD009. At first everyone said they were smooth and quiet and shift well, but I've been looking at other forums and Z people seem to think they're loud.

I know of one person who has a single mass flywheel on a Vr6 with this trans, and says it does the T5 neutral rattle thing really badly.

Curious to actually drive one of these.
They are about as loud as my Getrag 265 was. Usually they get louder with an upgraded clutch and single mass FW. It should be ok if you can adjust your idle a little north of 800 rpm.

I have one in my 370z Nismo but it has a single mass FW and an heavy duty clutch/PP. It's not the quietest tranny I've experienced but the shifting action is very nice.
poulrais is online now   Reply With Quote
Old 10-15-2018, 07:19 PM   #12
GreatDaneShane
Board Member
 
GreatDaneShane's Avatar
 
Join Date: Jul 2007
Location: Houston, Texas
Default

CBF performance sells a forward mount shifter that puts it near the stock m46/m47 shifter position, but the damn thing is 500 dollars.

https://cbfperformance.net/#!/Gen-3-...258/category=0
GreatDaneShane is offline   Reply With Quote
Old 10-15-2018, 07:42 PM   #13
JohnMc
PV Abuser
 
JohnMc's Avatar
 
Join Date: May 2004
Location: St. Louis
Default

/\ /\ /\ That's what I'm using. Fair warning - he said he had a thunderstorm at his shop that fried his mill, but when I bought mine it was a solid 3 1/2 months until he shipped it. Then he forgot the offset shifter handle and I still haven't gotten that, but he said Friday it's coming soon.
JohnMc is offline   Reply With Quote
Old 10-21-2018, 03:13 PM   #14
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default

Quote:
Originally Posted by JohnMc View Post
Looks like it's going behind an LS? I've got the same thing going on with my 240.

What motor mounts/oil pan are you using? The trans position you have there looks pretty close to mine. I'm using those STS mounts, but then I moved things forward about 1 1/4" just to make clearance issues on various things (bellhousing, steering column) go away.
I'm sticking it behind my b230ft, the reference pic of the trans in the tunnel under the shift hole is from a guy that LS swapped.
AndrewTheHobbit is offline   Reply With Quote
Old 10-21-2018, 03:15 PM   #15
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default

Quote:
Originally Posted by GreatDaneShane View Post
CBF performance sells a forward mount shifter that puts it near the stock m46/m47 shifter position, but the damn thing is 500 dollars.

https://cbfperformance.net/#!/Gen-3-...258/category=0
I'm not getting this unless I absolutely have to, For now I'm working on jerryrigging something to make the m47 shifter work with the stock pull up style reverse lockout.
AndrewTheHobbit is offline   Reply With Quote
Old 10-21-2018, 03:16 PM   #16
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default

Quote:
Originally Posted by poulrais View Post
Damn that thing is so shiny! Did you buy it brand new?
yepp! from z1 performance i believe, figured id do it right the first time and not have any worries.
AndrewTheHobbit is offline   Reply With Quote
Old 10-21-2018, 03:16 PM   #17
AndrewTheHobbit
Board Member
 
Join Date: Nov 2017
Location: Puyallup, WA
Default

Quote:
Originally Posted by t8fanning View Post
I'll be interested to see how it fits in the tunnel.
so would I, currently waiting on shipment from deeworks, might be a while.
AndrewTheHobbit is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 04:20 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.