• Hello Guest, welcome to the initial stages of our new platform!
    You can find some additional information about where we are in the process of migrating the board and setting up our new software here

    Thank you for being a part of our community!

740 + bbs rs

Mueller said:
I want to talk !@#$ about it due to those tires (or lack of, hahaha) but I cannot...car is too damn clean and cool looking!

Good job!
Click to expand...

Keep in mind that factory is either 195 or 205 tire.

CJM_RVA said:
Stanced 740 is stanced.

Damn, though, that's an incredible-looking car. Well done, sir!
Click to expand...

I would call that "Euro", stance is such over used phrase to describe them, we often forget that the earlier Euro style is just like this, accentuate OEM line, mint interior (no neon green Bentley stitching recaro seats), and nice wheels with a healthy amount of lowering.
 
2fast242gt said:
Where do you find barrels? I'd like some for my LM.
Click to expand...

The LM wheels are only two piece wheels, so the barrels for them are custom ordered from BBS = ****ing expensive.

The car looks AWESOME R?da!:)The perfect look, color, wheels, interior and all the attention to details makes this car perfect!:)
 
Chigga 744SE said:
Keep in mind that factory is either 195 or 205 tire.



I would call that "Euro", stance is such over used phrase to describe them, we often forget that the earlier Euro style is just like this, accentuate OEM line, mint interior (no neon green Bentley stitching recaro seats), and nice wheels with a healthy amount of lowering.
Click to expand...

Yea, it is the rim width to tire width ratio that is wrong :)
 
Thanks every one! :)

Here's a crappy video filmed the wrong way, but it's for the sound.

<iframe width="853" height="480" src="//www.youtube.com/embed/XUC9PFd8gmU?rel=0" frameborder="0" allowfullscreen></iframe>
 
Photobucket is being a dick


IMG_6367 by redblockk, on Flickr

IMG_6376 by redblockk, on Flickr

IMG_6381 by redblockk, on Flickr

IMG_6384 by redblockk, on Flickr

IMG_6388 by redblockk, on Flickr

IMG_6402 by redblockk, on Flickr

IMG_6408 by redblockk, on Flickr

IMG_6411 by redblockk, on Flickr

IMG_6412 by redblockk, on Flickr

IMG_6418 by redblockk, on Flickr

IMG_6420 by redblockk, on Flickr

IMG_6423 by redblockk, on Flickr

IMG_6433 by redblockk, on Flickr

IMG_6452 by redblockk, on Flickr

IMG_6457 by redblockk, on Flickr

IMG_6461 by redblockk, on Flickr

IMG_6464 by redblockk, on Flickr

IMG_6466 by redblockk, on Flickr

IMG_6470 by redblockk, on Flickr

IMG_6482 by redblockk, on Flickr

IMG_6486 by redblockk, on Flickr

IMG_6489 by redblockk, on Flickr

IMG_6492 by redblockk, on Flickr

IMG_6493 by redblockk, on Flickr
 
No idea, long time since i drove the engine when it was in the 960. But it shold be some improvement, the stock headers aren't the most optimal.

Ecu is stock
 
Are these RS 112's?
What was the original inner barrel width?

And did you happen to try to fit the 6" inner barrels on a 240 (and did that fit if you did?)?
I have four RS112 5x108 centers and want to build up a set too.

Thanks!
 
It’s RS 262 and 263 that I re-drilled to 5/108.

This is 5.5 inner barrels now, pretty tight but I’m not sure if the centers have different offset in themselves. The original barrels was 7 and 7.5
 
R?da said:
It?s RS 262 and 263 that I re-drilled to 5/108.

This is 5.5 inner barrels now, pretty tight but I?m not sure if the centers have different offset in themselves. The original barrels was 7 and 7.5
Click to expand...


Ok, thanks. I think the centers are always 0,5J.
I will go fo 5.5 inner barrels too then and 2J outer lips.
so the total will be 8J.

Not sure yet if I go 16" or 17". Hope it will all fit ;-)
 
You must log in or register to reply here.
Back
Top