Recent content by Dawson

So I believe I've sourced all my parts. Just want to make sure I'm not leaving anything out here. 1) Lynx manifold from Eric @ Hi Performance 2) Weber 45mm DCOE (x2) from Carbs Unlimited 3) Redline "soft mount" kit (x2) also from Carbs Unlimited 4) Redline Linkage bar kit for dual DCOE From...

So here goes, the car has a B20 from a 142 in it and already had an alternator (Bosch 35 amp) which worked completely fine the entire time I've had this car (maybe 1000 miles or so). Anywho, the Bosch went out in big time, like marbles in the case sounds. So I figured now would be a good time...

Built up a motor for my car ('91 240) running green tops, resistor pack spliced in, turbo EZK and ECU. I have no idle where this problem is coming from!! It runs smooth if I hold my foot on the gas whether the motor is hot or cold, but as soon as I let off it dies right out... Here is a list...

N/A, B230F, M47, stock LH2.4 I'm not sure what it could be? I just replaced my fuel filter the other day with no change. I had this same problem about a year ago and just kept throwing parts at the car til it went away. Now I'm kind of at a loss. It starts fine when cold and idles ok. Under...

I know a few of you guys have made them... I'd like to do one for myself. Lemme see some of the designs you came up with! Thanks guys!!

I just bought another non running 240 but I haven't picked it up yet... When I first asked what was wrong with it, the girl said the fuel pump was dead. Then when we were just talking about the car she mentioned the shop told her the pump "wasn't getting power"... What you guys think? Maybe just...

Black Ice + Guard Rail x Exit Ramp = Epic Fail

I plan on swapping everything from my '91 240 into my '78 260. The 260 has the PRV and is 100% stock with the k-jet. I'm going to put the b230f in it w/ 2.4 injection. What is entailed in a swap like this? The motor swap itself is very straight forward and I'm not worried about that. It's just...

I found one... Guy wants 100 bucks for it. Is this any good?

FCP and IPD don't carry it. The dealer is giving me some crap that it only comes as an entire assembly and needs to be painted for $606.00!!! WTF, I just want the gasket seal thinger!! The car is a '92, its in the sig. Where do you 940 guys find these seals?

Car in my sig, B230f, M47, lh2.4... A few weeks ago I had this problem where the RPM's would die when I clutched in coming to a stop now and again. At first it was once in a while (like once every couple days) then after about a week it got progressively worse (like 5 times each trip out). The...

So the story goes, I bought a set of Hydras and one was fubared. I used JB weld to keep the center cap in place and it worked for over a year. then one day the center cap just decided to emancipate itself from my car... Oh well, time for something new!! I've had an extra set of Virgos...

Yes... It may be a noob question and I did search but I saw nothing about direct swapability. I think my original 206k N/A fuel pumps are on their way out. Can I buy the pumps for a same year 740 Turbo and throw them right into my 240 (teh silver one in sig)??? Reason I ask is because while they...

1991 240 B230F, AW70 Working on swapping in my M47 and I'm wondering how the torque converter is connected up in there... After I get all the trans bolts out can I just slide the AW off or do I need to unbolt anything from the flex plate?? Thanks guys!

Next week the M47 goes in and I don't want any hang ups... Let me know if you see anything important missing from this list.. Thanks! This is all going into my '91 244 b230f currently w/ an AW70. So far I've got: M47 w/ bell housing and shift linkage Short throw shifter (Aspirator) Freshly...