home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: philski o'flood
Forum: maintenance & nonperformance 09-21-2022, 01:39 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
if it ran it got hot

if it ran it got hot
Forum: maintenance & nonperformance 09-21-2022, 01:31 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
bolts torqued down and never got hot you'd...

bolts torqued down and never got hot you'd probably be ok re-using, I have done this and it's held for 4-5 years now, but not a turbo
bolts torqued down and engine hot forget it, you need a new one
Forum: maintenance & nonperformance 09-21-2022, 12:24 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
yeah I dunno know...

yeah I dunno know...
Forum: maintenance & nonperformance 09-18-2022, 02:43 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
ok wow and a +t lots going on... probably don't...

ok wow and a +t lots going on... probably don't need to send anything to a machine shop.
Forum: maintenance & nonperformance 09-18-2022, 01:45 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
seems like there is a lot of back story here... ...

seems like there is a lot of back story here...

so you replaced the head and then ?... then tried to start it but it never started ? ...

but you cranked it for sometime and that was enough to...
Forum: maintenance & nonperformance 09-16-2022, 03:59 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
I said use a scotch brite on that one cap and...

I said use a scotch brite on that one cap and then, obviously :),
you wash away any dirt grime grease or left over bits of green scrubby before you install it

wire wheel on cam
green scrubby on...
Forum: maintenance & nonperformance 09-16-2022, 02:35 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
do you know "escoboy" Neil? he is a real...

do you know "escoboy" Neil? he is a real knowledgable mechanic and lives in Esco
Forum: maintenance & nonperformance 09-16-2022, 02:25 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
can you repair the cam? as in replace the pin?...

can you repair the cam? as in replace the pin? Marshall's Hardware on Miramar Rd. should the correct size roll pin for it

Forget checking the clearance it doesn't matter since you can't change it...
Forum: maintenance & nonperformance 09-16-2022, 01:52 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
the older ones have the large belt guide pieces...

the older ones have the large belt guide pieces on either side of the gear no washer behind them
Forum: maintenance & nonperformance 09-16-2022, 01:48 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
does it have a notch for the pin?

does it have a notch for the pin?
Forum: maintenance & nonperformance 09-16-2022, 12:53 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
Washer on back side of cam gear? So like Gear...

Washer on back side of cam gear? So like Gear > Washer > Camshaft

Never ever seen that....

The washer most likely caused the cam pin failure by not allowing it to sit down properly and...
Forum: maintenance & nonperformance 09-15-2022, 10:31 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
timing belt

timing belt
Forum: maintenance & nonperformance 09-12-2022, 10:33 PM
Replies: 116
Views: 9,768
Posted By philski o'flood
2 years!?! Cranks but no start... fuel pump...

2 years!?!

Cranks but no start... fuel pump relay, crank position sensor, What ECU is in it... um it's got gas and a good fuel pump right?

Did you ever have it running?
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -4. The time now is 11:29 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.