home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 300
Search took 0.05 seconds.
Search: Posts Made By: cwdodson88
Forum: performance & modifications Today, 12:06 PM
Replies: 33
Views: 392
Posted By cwdodson88
These are twin complete rotor/stators that share...

These are twin complete rotor/stators that share a common shaft. Yes, it does require dual inverters, but by running them this way, you have both failsafe, and split load. The power electronics are...
Forum: performance & modifications Today, 11:11 AM
Replies: 33
Views: 392
Posted By cwdodson88
Our signature "Dual Stack" runs around 800-850 nm...

Our signature "Dual Stack" runs around 800-850 nm on the shaft. Depending on the power electronics and Voltage behind it, you can expect to see full torque up to about 8000rpm. At 800v I'd say that...
Forum: performance & modifications Today, 10:41 AM
Replies: 33
Views: 392
Posted By cwdodson88
I built a motor for a e-1800. Made right about...

I built a motor for a e-1800. Made right about 900hp on my dyno. Theyre set up to put down about 522kw (~700hp) peak burst, with about 400kw continuous with their battery bank and inverter setup. If...
Forum: performance & modifications Today, 10:23 AM
Replies: 33
Views: 392
Posted By cwdodson88
Thats been available for a while, the e-copo was...

Thats been available for a while, the e-copo was not the first... I personally built that motor. Also the motors for the Genovation GXE, LS platform Z06's, and the E-Cobra Jet. All of those motors...
Forum: performance & modifications 05-04-2021, 11:26 AM
Replies: 3
Views: 1,031
Posted By cwdodson88
Really, sizing a pump is going to depend on how...

Really, sizing a pump is going to depend on how much oil your block can flow. Without knowing that, you're just guessing. And without any information as to what engine youre wanting to put a dry sump...
Forum: maintenance & nonperformance 04-30-2021, 11:30 AM
Replies: 78
Views: 4,088
Posted By cwdodson88
Shims go under the spring.

Shims go under the spring.
Forum: maintenance & nonperformance 04-29-2021, 06:19 PM
Replies: 29
Views: 1,604
Posted By cwdodson88
just because the gaskets are new doesnt mean they...

just because the gaskets are new doesnt mean they cant leak. A warped surface, burr from a drop, residual gasket from disassembly, improper torque spec, improper torque sequence can all leave you...
Forum: projects & restorations 03-29-2021, 04:35 PM
Replies: 36
Views: 18,284
Posted By cwdodson88
Comes in really handy when you have to blend, but...

Comes in really handy when you have to blend, but dont want to go all the way to a panel edge.

I also do the same with door jambs and such. tape on the back of the door, close it and use a razor...
Forum: projects & restorations 03-29-2021, 03:00 PM
Replies: 36
Views: 18,284
Posted By cwdodson88
NICE WORK!!! Noticed when you did the paint...

NICE WORK!!!

Noticed when you did the paint touchup on the rear wing/mudguard area that you "hard" masked it. Just a note, or something to try in the future when doing spot touchups like that,...
Forum: performance & modifications 03-29-2021, 12:31 PM
Replies: 19
Views: 2,215
Posted By cwdodson88
<iframe width="560" height="315"...

<iframe width="560" height="315" src="https://www.youtube.com/embed/61DcZpBhoqo" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media;...
Forum: maintenance & nonperformance 03-25-2021, 05:43 PM
Replies: 12
Views: 1,474
Posted By cwdodson88
or another car... MG, Triumph, Austin Healey,...

or another car... MG, Triumph, Austin Healey, Austin Mini all used a smiths cable driven tach at some point in their generations.
Forum: performance & modifications 03-25-2021, 12:41 PM
Replies: 25
Views: 3,430
Posted By cwdodson88
Sounds like you've got it handled. I vote go for...

Sounds like you've got it handled. I vote go for it! If you find a recipe that works it might be worth it to someone.
Forum: performance & modifications 03-25-2021, 10:42 AM
Replies: 25
Views: 3,430
Posted By cwdodson88
My rods are spec'd for my b20 build. But it seems...

My rods are spec'd for my b20 build. But it seems you're missing the point. I paid under $400/shipped for a set of custom engineering samples. I was told that a bulk order of 25 sets (100 rods min)...
Forum: performance & modifications 03-24-2021, 06:19 PM
Replies: 25
Views: 3,430
Posted By cwdodson88
See if they would do a Peugeot 306 rod with BE...

See if they would do a Peugeot 306 rod with BE diameter opened up to 58mm and small end at 24. Pretty sure they would.
Forum: performance & modifications 03-24-2021, 06:15 PM
Replies: 25
Views: 3,430
Posted By cwdodson88
Thats just it, they offer a 158 for something...

Thats just it, they offer a 158 for something else.... and since they are the manufacturer, they have blanks, then can bore the big end where you want and as big as you want, same with the small end...
Forum: performance & modifications 03-24-2021, 05:43 PM
Replies: 25
Views: 3,430
Posted By cwdodson88
You do know that MaxpeedingRod will make you a...

You do know that MaxpeedingRod will make you a 4340 Forged H beam in just about any length/width/se bore/be bore... for less than 400$/set shipped, right?

Just got mine back from a trip to Stack...
Forum: maintenance & nonperformance 03-24-2021, 11:17 AM
Replies: 24
Views: 2,495
Posted By cwdodson88
Joe Cuturo has a couple good ones. For jigs,...

Joe Cuturo has a couple good ones. For jigs, fixtures, ect, most of these were assembled and pinned by hand, so they're all different. My favorite jig, green loctite, and a roll of lockwire :rofl:
...
Forum: maintenance & nonperformance 03-23-2021, 11:37 AM
Replies: 24
Views: 2,495
Posted By cwdodson88
By my count, there are 5-7 good SU guys to send...

By my count, there are 5-7 good SU guys to send stuff to. Most are in their late 50s and sometimes have longer than desired lead times. So, the way I see it, learn their craft and carry on the...
Forum: maintenance & nonperformance 03-23-2021, 11:22 AM
Replies: 24
Views: 2,495
Posted By cwdodson88
Theres also Rhys Kent in the Seattle area. Hes...

Theres also Rhys Kent in the Seattle area. Hes always done a good job for me. But I have recently received all the tooling to handle them myself.

For the throttle shaft pin locations, thats...
Forum: maintenance & nonperformance 03-18-2021, 10:26 AM
Replies: 24
Views: 2,495
Posted By cwdodson88
oilite bronze bushings from McMaster Carr, 3/8...

oilite bronze bushings from McMaster Carr, 3/8 od, use a .375 reamer and dont drop it all the way through, leave 1-3/32 of original body near the ID of the throat so the butterfly seals, and glue the...
Forum: projects & restorations 03-15-2021, 01:01 PM
Replies: 102
Views: 62,650
Posted By cwdodson88
I'd make sure it holds your boost pressure +25%,...

I'd make sure it holds your boost pressure +25%, but that would be assuming that your cam will allow all the valves to be closed when testing. Or remove the cam and test both sides, intake and...
Forum: projects & restorations 03-15-2021, 11:32 AM
Replies: 102
Views: 62,650
Posted By cwdodson88
if all the valves are closed, I'd expect that you...

if all the valves are closed, I'd expect that you could pump it to 30 psi for 30 min with no pressure drop. Or at least pass the soapy water test. If it were me, I'd glue that adapter down with Ultra...
Forum: maintenance & nonperformance 03-08-2021, 12:46 PM
Replies: 17
Views: 2,087
Posted By cwdodson88
That'll do all sorts of weird stuff.

That'll do all sorts of weird stuff.
Forum: maintenance & nonperformance 03-02-2021, 12:18 PM
Replies: 17
Views: 2,087
Posted By cwdodson88
OP- are you using the phenolic spacers? If not,...

OP- are you using the phenolic spacers? If not, I'd try that. Rather than flooring it, you could try adjusting the choke cam so that it cracks the throttle before it drops the jet. I think I ended up...
Forum: performance & modifications 03-01-2021, 06:05 PM
Replies: 4
Views: 1,142
Posted By cwdodson88
summitracing

summitracing
Forum: aftermarket engine management 03-01-2021, 03:46 PM
Replies: 4
Views: 1,382
Posted By cwdodson88
I used an old brake light switch on my 122. Wired...

I used an old brake light switch on my 122. Wired per MS manual on a proto board that is actually the bracket for the switch. Then a switch on the dash to turn it on or off. Mine is adjusted so that...
Forum: performance & modifications 02-16-2021, 04:05 PM
Replies: 62
Views: 16,269
Posted By cwdodson88
what all is involved in the TKO adapter as far as...

what all is involved in the TKO adapter as far as bellhousing machining? just opening up the bore?
Forum: performance & modifications 02-16-2021, 02:05 PM
Replies: 62
Views: 16,269
Posted By cwdodson88
I'm just about to pull the trigger. My t5 is...

I'm just about to pull the trigger. My t5 is tired... I went through it, billet cluster support, bells, whistles, upgraded g-force main shaft, then ended up twisting the 1-2 selector spline far...
Forum: performance & modifications 02-16-2021, 01:43 PM
Replies: 62
Views: 16,269
Posted By cwdodson88
looks like tremec is offering up a TKX. 5 speed...

looks like tremec is offering up a TKX. 5 speed manual synchro box, 600ftlb rated and RPM good up to 7500. Biggest plus is that it comes in smaller than the tko500/600 and has higher rev ranges than...
Forum: performance & modifications 02-09-2021, 04:18 PM
Replies: 28
Views: 4,315
Posted By cwdodson88
you could move out of Cali. Might be easier.

you could move out of Cali. Might be easier.
Forum: performance & modifications 02-09-2021, 02:36 PM
Replies: 28
Views: 4,315
Posted By cwdodson88
Magnaflow CARB Cat, and Magnaflow straight...

Magnaflow CARB Cat, and Magnaflow straight through muffler. Just spend the money.
Forum: performance & modifications 02-09-2021, 12:26 PM
Replies: 60
Views: 7,470
Posted By cwdodson88
Totally aware... Although I dont plan to beat on...

Totally aware... Although I dont plan to beat on it too hard since I've been overpowering my trans since the last turbo/IC setup. I have started designing a billet head just in case. I've got 3...
Forum: projects & restorations 02-05-2021, 06:51 PM
Replies: 196
Views: 91,123
Posted By cwdodson88
I would do this: (3) 6x6" 1/8" steel plate. ...

I would do this:

(3) 6x6" 1/8" steel plate.
(3) nuts that fit the original bolts including the front center eyelet.

Drill holes in the current floor where the new seat mounts need to be that...
Forum: performance & modifications 02-05-2021, 04:54 PM
Replies: 60
Views: 7,470
Posted By cwdodson88
I just had a set of Gary's gstellsr valves...

I just had a set of Gary's gstellsr valves installed, 46/38's :omg: and they're sitting about 0.008-0.010" apart. Had to have then intake seats installed, then the exhaust seat cut to overlap the...
Forum: performance & modifications 02-02-2021, 09:51 PM
Replies: 60
Views: 7,470
Posted By cwdodson88
That dude is super cool. Easy af to talk to. ...

That dude is super cool. Easy af to talk to.

I vote for cc the chambers after you take a deburr knife or file to the edges and give them a solid 2mm radius.

Then measure bore, deck height,...
Forum: projects & restorations 01-11-2021, 03:14 PM
Replies: 412
Views: 208,828
Posted By cwdodson88
2 forward, 3 back. Jurbski sounds great,...

2 forward, 3 back.

Jurbski sounds great, looks great, and everything worked, got the water meth set points established But had some catastrophic failures. Should have known that something was up...
Forum: performance & modifications 12-20-2020, 01:51 PM
Replies: 11
Views: 2,217
Posted By cwdodson88
B18-20 hybrid=garbage. Don’t waste your time. The...

B18-20 hybrid=garbage. Don’t waste your time. The chamber mushrooms over the bore, no bueno. Not a huge difference between k and d. Less overlap, so if injected you can get some more miles depending...
Forum: performance & modifications 12-02-2020, 12:46 PM
Replies: 27
Views: 4,464
Posted By cwdodson88
Rhys is the only person I will send stuff to...

Rhys is the only person I will send stuff to anymore. Had 3 different people "rebuild" sets of carbs for me for different cars, Austins, MG's, Triumphs... Rhys was the only one that I did not have...
Forum: maintenance & nonperformance 10-27-2020, 10:13 AM
Replies: 5
Views: 1,510
Posted By cwdodson88
Pull the pins, measure and hit McMaster

Pull the pins, measure and hit McMaster
Forum: projects & restorations 10-23-2020, 10:34 AM
Replies: 196
Views: 91,123
Posted By cwdodson88
One other thing would be a wet vs dry compression...

One other thing would be a wet vs dry compression test, or a good leak down test.
Forum: projects & restorations 10-22-2020, 01:19 PM
Replies: 196
Views: 91,123
Posted By cwdodson88
That seems low

That seems low
Forum: maintenance & nonperformance 10-22-2020, 12:29 PM
Replies: 19
Views: 3,096
Posted By cwdodson88
I've always dropped the tailshaft of the trans...

I've always dropped the tailshaft of the trans 3-4", tipped the engine back, and using a load leveler and hoist went forward until the input shaft cleared then straight up.

Most recently, I just...
Forum: projects & restorations 10-20-2020, 02:42 PM
Replies: 196
Views: 91,123
Posted By cwdodson88
Surfaces and finish generally arenít the problem....

Surfaces and finish generally arenít the problem. Sometimes you canít see it, but after machining, if someone dented the side it will raise a spot on the mating surface. Running an oil stone over it...
Forum: projects & restorations 10-15-2020, 10:55 AM
Replies: 102
Views: 62,650
Posted By cwdodson88
I have found that some chargers dont like...

I have found that some chargers dont like charging a battery that is below 10v. Sometimes if you trick your charger, by connecting a "good" battery in parallel with some jumper cables, it'll take the...
Forum: projects & restorations 10-15-2020, 10:50 AM
Replies: 196
Views: 91,123
Posted By cwdodson88
Id say that your persistent high idle is most...

Id say that your persistent high idle is most likely an air leak. If the rear carb is "sucking" more, I'd look at the front carb. Are you using the aluminum intake? those have a freeze plug in the...
Forum: performance & modifications 10-12-2020, 04:43 PM
Replies: 76
Views: 19,370
Posted By cwdodson88
My T5 with 3.35 first with 3.73 gears is...

My T5 with 3.35 first with 3.73 gears is borderline stupid. First gear to 35-38, second to damn near 70, which is all fine unless you're trying to drive in populated areas. Sucked at local short...
Forum: performance & modifications 10-01-2020, 04:18 PM
Replies: 34
Views: 6,019
Posted By cwdodson88
https://dailyturismo.com/3k-suicide-seats-1969-vol...

https://dailyturismo.com/3k-suicide-seats-1969-volvo-142-ford-v8/
http://2.bp.blogspot.com/-30-fdqIb62U/UiF4Cni5j3I/AAAAAAAAQzw/VtqNNAQ1z2o/s1600/1a.jpg
Forum: performance & modifications 10-01-2020, 03:52 PM
Replies: 2
Views: 1,396
Posted By cwdodson88
Remove the FPR from that location and install a...

Remove the FPR from that location and install a "T" attach the T to both sides of that rail, and the 3rd leg to your feed. Use the port you have labeled as "fuel" to run to the FPR, and the outlet of...
Forum: performance & modifications 10-01-2020, 11:20 AM
Replies: 4
Views: 1,837
Posted By cwdodson88
https://cdn.shopify.com/s/files/1/0260/2623/produc...

https://cdn.shopify.com/s/files/1/0260/2623/products/wWXVnVS_1024x1024.jpeg?v=1600113125

From this picture, it looks like the steel plates just sandwich the factory location after trimming the...
Forum: performance & modifications 09-30-2020, 05:58 PM
Replies: 12
Views: 2,745
Posted By cwdodson88
The sedan is much shorter on the fill tube side. ...

The sedan is much shorter on the fill tube side.

I used a "Bulkhead" style hose fitting for my return. Drilled an appropriate size hole in the fuel level sender. So far, no leaks, and it also...
Showing results 1 to 50 of 300

 
Forum Jump

All times are GMT -4. The time now is 04:12 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.