home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 50 of 229
Search took 0.02 seconds.
Search: Posts Made By: DavePolyakov
Forum: maintenance & nonperformance 09-19-2021, 10:53 AM
Replies: 11
Views: 529
Posted By DavePolyakov
I just reinstalled it with silicone I didn't have...

I just reinstalled it with silicone I didn't have time. What flat surface should I use if I do this in the future?
Forum: maintenance & nonperformance 09-17-2021, 02:38 PM
Replies: 11
Views: 529
Posted By DavePolyakov
The clutch also grabs right off the floor. Like...

The clutch also grabs right off the floor. Like right off the floor. Probably should adjust it a little looser? I can inspect clutch and pilot bearing, I have a transmission jack.
Forum: maintenance & nonperformance 09-17-2021, 12:55 AM
Replies: 11
Views: 529
Posted By DavePolyakov
The fluid was quite red. Even driving today with...

The fluid was quite red. Even driving today with all new fluid, it's extremely hard to shift. It's gotten worse. I don't know if I need new bushings or what, but its hard to shift into all gears, 3-4...
Forum: maintenance & nonperformance 09-16-2021, 06:30 PM
Replies: 7
Views: 1,006
Posted By DavePolyakov
I'm ordering hoses to reinstall stock AMM and I...

I'm ordering hoses to reinstall stock AMM and I need another resistor pack to reinstall stock injectors. If anyone has a resistor pack for cheap give me a PM.
Forum: maintenance & nonperformance 09-16-2021, 01:17 PM
Replies: 7
Views: 1,006
Posted By DavePolyakov
I replaced the O2 sensor and swapped in another...

I replaced the O2 sensor and swapped in another AMM. Neither of these solved the stalling issue and funky idle. So it must be the 3-inch exhaust, eBay 36lb/hr injectors, or the fact I have a 3-inch...
Forum: maintenance & nonperformance 09-16-2021, 02:43 AM
Replies: 11
Views: 529
Posted By DavePolyakov
Only a little more than a quart of oil came...

Only a little more than a quart of oil came out...

The drain plug.

https://i.postimg.cc/6qNFrMq9/IMG-2732.jpg
Forum: maintenance & nonperformance 09-15-2021, 05:01 PM
Replies: 11
Views: 529
Posted By DavePolyakov
What happened to my m46 overdrive sump??

Went to change the fluid in my m46, noticed the sump surface is full of scratches and there are even two small cracks in the bolt holes. Would adding silicone then installing the gasket be my best...
Forum: projects & restorations 09-06-2021, 07:10 AM
Replies: 27
Views: 6,459
Posted By DavePolyakov
I just checked the listing for the adapter on...

I just checked the listing for the adapter on Deeworks. I think he’s added more details on the correct input shaft. I think the description was different when I bought mine. Now it’s very clear which...
Forum: projects & restorations 09-05-2021, 10:15 AM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Yeah, I live near Seattle, lots of long rainy...

Yeah, I live near Seattle, lots of long rainy dark cold days. Besides, the felt is partly detatched/destroyed and I never open the roof anyways. Whenever I do open it I need to hold the felt in place...
Forum: projects & restorations 09-05-2021, 06:38 AM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Thanks! I ordered the gel version, can’t wait to...

Thanks! I ordered the gel version, can’t wait to see the improvement. I really need to replace the headliner and I want to do a sunroof delete, just not sure the best way to go about it right now.
Forum: projects & restorations 09-03-2021, 03:54 AM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Picked up these 16x8 aluminum wheels for a decent...

Picked up these 16x8 aluminum wheels for a decent price a while ago and got them mounted with 225x50s. I’m not sure of the offset, I think its 0. Ebay 25mm spacers in the front and 32mm in the rear....
Forum: maintenance & nonperformance 09-02-2021, 05:35 AM
Replies: 7
Views: 1,006
Posted By DavePolyakov
Anyone? I tried to make my post more concise. Any...

Anyone? I tried to make my post more concise. Any tips on fixing the issue with the car dying and weird idle? I just want to maximize performance on my setup with a 15g with turbo cam and lh2.4. My...
Forum: maintenance & nonperformance 08-28-2021, 07:46 AM
Replies: 7
Views: 1,006
Posted By DavePolyakov
Only engine mods are IPD turbo cam, 012 amm and...

Only engine mods are IPD turbo cam, 012 amm and 36lb/hr white injectors. I have another 012 I will swap in and see if that solves the issue, however Im skeptical thats the issue because the problem...
Forum: maintenance & nonperformance 08-27-2021, 10:39 AM
Replies: 7
Views: 1,006
Posted By DavePolyakov
02 sensor contaminated?

I removed my o2 sensor for the first time when upgrading my exhaust. It was my first time seeing an o2 sensor, I meant to be careful but the tip of ceramic kissed some grease in the engine bay. Car...
Forum: performance & modifications 08-23-2021, 08:22 PM
Replies: 13
Views: 1,472
Posted By DavePolyakov
Check my project thread for my 740 I just posted...

Check my project thread for my 740 I just posted how I did mine. I tapped into the headlight switch for power.
Forum: projects & restorations 08-22-2021, 08:37 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
I got the injectors and installed them. The car...

I got the injectors and installed them. The car idled a little smoother and pulled slightly harder from what I could tell compared to the green giants.

On the weekend a full 3-inch exhaust popped...
Forum: performance & modifications 08-19-2021, 10:07 AM
Replies: 4
Views: 1,198
Posted By DavePolyakov
I have an aftermarket cable clutch in my 740 with...

I have an aftermarket cable clutch in my 740 with stage 2 Yoshifab t5 clutch components. There are some small parts you need for the clutch cable connections at the pedal and the clutch fork which...
Forum: projects & restorations 08-16-2021, 06:52 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
I ordered some aftermarket 0-280-155-811...

I ordered some aftermarket 0-280-155-811 injectors that flow 380cc/min or 36lb/hr.

They were $38 for six injectors, predictions if they work?
Forum: projects & restorations 08-14-2021, 02:37 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
To get a tune for the 012 AMM I either need chips...

To get a tune for the 012 AMM I either need chips or a standalone ecu correct? I had to hack up my airbox to fit the 012, I can’t go back to the 016 unless I get another top half of the airbox and...
Forum: projects & restorations 08-13-2021, 08:48 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Is this Bosch 0-280-155-766 that flows at...

Is this Bosch 0-280-155-766 that flows at 33.3lb/hr?
Forum: projects & restorations 08-12-2021, 01:46 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
All I've done is remove the #1 fuse for the fuel...

All I've done is remove the #1 fuse for the fuel ECU for 1-2 minutes. I believe this will reset the fuel ecu. I am in the process of looking for the right chips as I'm sure they would help. Redblock...
Forum: projects & restorations 08-12-2021, 12:43 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Small update, I sourced a 012 3 inch AMM and 42...

Small update, I sourced a 012 3 inch AMM and 42 lb/hr green giant injectors. Below is a picture of how I adapted the 012 AMM to work in the stock location with the stock airbox. I bought some 2.75"...
Forum: maintenance & nonperformance 08-10-2021, 08:33 PM
Replies: 18
Views: 2,040
Posted By DavePolyakov
Very much so. I wonder if this loose hose...

Very much so. I wonder if this loose hose connection was causing occasional break-ups when in boost. I want to let the ECU adjust for a few hundred miles before I start boosting again but I'm curious...
Forum: maintenance & nonperformance 08-09-2021, 04:19 PM
Replies: 18
Views: 2,040
Posted By DavePolyakov
I am such a fool. The idle air control...

I am such a fool.

The idle air control valve hose had slipped off of the intake manifold. I didn't notice it because it's under all the other hoses and hard to access. Now the car starts and...
Forum: maintenance & nonperformance 08-09-2021, 03:50 PM
Replies: 18
Views: 2,040
Posted By DavePolyakov
Kind of what I've been wondering, it seems like a...

Kind of what I've been wondering, it seems like a coincidence the AMM would quit at 6k under full boost. If I remember I think there may have been a popping sound. I'll do a thorough check, it must...
Forum: maintenance & nonperformance 08-09-2021, 03:35 PM
Replies: 18
Views: 2,040
Posted By DavePolyakov
I verified the MAF is getting 12v and I tested...

I verified the MAF is getting 12v and I tested the ground wire too, It measured 1.2 ohms when I tested using the negative terminal as the ground. The ohms between pin 2 and 3 on the AMM measure 3.9...
Forum: maintenance & nonperformance 08-09-2021, 12:21 AM
Replies: 18
Views: 2,040
Posted By DavePolyakov
I've since tested two other AMM's and the same...

I've since tested two other AMM's and the same issue. The car throws code 2-3-2, "Fuel trim (lambda control) too lean or too rich at idle".

The issue began when I was at 12 pounds of boost and...
Forum: maintenance & nonperformance 08-08-2021, 12:05 PM
Replies: 18
Views: 2,040
Posted By DavePolyakov
This is what I thought but wanted to make sure....

This is what I thought but wanted to make sure. Guess I need to find another 012 AMM.
Forum: maintenance & nonperformance 08-08-2021, 11:34 AM
Replies: 18
Views: 2,040
Posted By DavePolyakov
Only runs without AMM plugged in

1990 740 b230ft. The car only runs with the AMM unplugged. I got a 3-inch AMM and larger injectors but I'm still having the same issues with this "new" used AMM.

If the car only runs with the AMM...
Forum: projects & restorations 07-09-2021, 02:21 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
I'm currently on the hunt for a good condition...

I'm currently on the hunt for a good condition 016 maf but I've really been thinking about making some power upgrades now that I've got my t5 installed for several months now. I don't have a power...
Forum: projects & restorations 07-07-2021, 05:01 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
The car will only run for 2 seconds then die....

The car will only run for 2 seconds then die. Unplugged the maf, the car now runs rough and idles around 1,5k, jumping up and down in the revs without any throttle input. Is there a possibility the...
Forum: projects & restorations 07-05-2021, 07:23 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
No rips/ tears or any damage to any piping. All...

No rips/ tears or any damage to any piping. All clamps are nice and tight. I checked the timing marks and the belt did not slip. The timing is still correct.
Forum: projects & restorations 07-05-2021, 06:04 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Compression tested: Cyl 1: 125 Cyl 2: 130 ...

Compression tested:

Cyl 1: 125
Cyl 2: 130
Cyl 3: 135
Cyl 4: 125

The car currently starts up, jumps to like 2-3k then dies immediately. Can't get it to idle. Sound ok though from 2-3k. The...
Forum: projects & restorations 07-05-2021, 02:56 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
It's a stock 1990 740 turbo only with a 15g...

It's a stock 1990 740 turbo only with a 15g turbo. Completely stock everywhere else. Doing a compression test soon. I can't really get the car to operating temp anymore because it's barely running....
Forum: projects & restorations 07-04-2021, 07:56 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Two hours ago I went wot in 1st, hit limiter a...

Two hours ago I went wot in 1st, hit limiter a little more than I anticipated, white smoke immediately spewed through the shifter hole into the cabin and the car stumbled for several seconds then...
Forum: maintenance & nonperformance 06-30-2021, 03:07 PM
Replies: 29
Views: 5,776
Posted By DavePolyakov
I just cleaned all PCV components. The plugs look...

I just cleaned all PCV components. The plugs look ok though right? The issue probably lies elsewhere?
Forum: maintenance & nonperformance 06-30-2021, 02:47 PM
Replies: 29
Views: 5,776
Posted By DavePolyakov
Pulled my spark plugs they each had a gap around...

Pulled my spark plugs they each had a gap around 0.028-0.030. I noticed the threads were oily. I've been told by my friends that when I'm boosting in front of them on the road they see black smoke...
Forum: maintenance & nonperformance 06-27-2021, 06:55 PM
Replies: 9
Views: 1,728
Posted By DavePolyakov
I successfully got it but It was very difficult....

I successfully got it but It was very difficult. Seriously fiddled around with it for a full hour just trying to thread it on. If the rubber seal was 1mm thinner I'm sure it would have been so much...
Forum: maintenance & nonperformance 06-27-2021, 03:34 PM
Replies: 9
Views: 1,728
Posted By DavePolyakov
Like using a C clamp to put pressure downward on...

Like using a C clamp to put pressure downward on the cap while screwing it by hand? I'm pretty damn sure you need to apply a lot of pressure to move the seal out of the way when threading it so the...
Forum: maintenance & nonperformance 06-27-2021, 02:45 PM
Replies: 29
Views: 5,776
Posted By DavePolyakov
Will pull my plugs and check the gap. Thanks for...

Will pull my plugs and check the gap. Thanks for the advice
Forum: maintenance & nonperformance 06-27-2021, 02:38 PM
Replies: 9
Views: 1,728
Posted By DavePolyakov
Motive power bleeder will not screw on

Been trying for the last hour, pushing down very hard, and keeping the cap square I still can not get it to thread onto the reservoir. Spilled a full liter of brake fluid in my driveway and my hands...
Forum: maintenance & nonperformance 06-27-2021, 10:59 AM
Replies: 29
Views: 5,776
Posted By DavePolyakov
They were both brand new before I had this issue....

They were both brand new before I had this issue. Less than a week since I installed them. It's now been three weeks since I installed the new CPS and I've not had the issue persist. My only concerns...
Forum: performance & modifications 06-27-2021, 02:10 AM
Replies: 259
Views: 124,854
Posted By DavePolyakov
So it won't be in spec...:lol::lol:

So it won't be in spec...:lol::lol:
Forum: performance & modifications 06-26-2021, 08:21 PM
Replies: 259
Views: 124,854
Posted By DavePolyakov
Right. So there is no solution?

Right. So there is no solution?
Forum: performance & modifications 06-26-2021, 02:47 PM
Replies: 259
Views: 124,854
Posted By DavePolyakov
I'm assuming the only adjustment would be through...

I'm assuming the only adjustment would be through an adjustable panhard bar? I'm almost sure my driveshaft angles in the vertical plane are properly set to have no vibration. Pretty sure there is a...
Forum: performance & modifications 06-25-2021, 03:04 PM
Replies: 259
Views: 124,854
Posted By DavePolyakov
Would there be compound angles in a 740?

Would there be compound angles in a 740?
Forum: maintenance & nonperformance 06-21-2021, 06:40 PM
Replies: 5
Views: 2,085
Posted By DavePolyakov
Can someone elaborate a little bit more? I'm...

Can someone elaborate a little bit more? I'm still unsure what you guys are proposing I try to get the seatbelt to work.
Forum: projects & restorations 06-16-2021, 02:53 PM
Replies: 27
Views: 6,459
Posted By DavePolyakov
Dave's 1990 740 Turbo Wagon T5 Manual

I should have started my project thread when I started the project. Now I have already finished the T5 swap in my 740 and I will cover everything I did as well as other things. I will do my best to...
Forum: maintenance & nonperformance 06-15-2021, 09:18 PM
Replies: 5
Views: 2,085
Posted By DavePolyakov
Replaced 740 seats, seatbelt is stuck?

As the title says. Put in newer seats and the passenger side seatbelt is locked after I reinstalled the seat belt onto the new seat. There's no issue with the system under the B pillar, I already...
Forum: performance & modifications 06-13-2021, 12:47 PM
Replies: 259
Views: 124,854
Posted By DavePolyakov
Thanks, I'll definitely check it out. I currently...

Thanks, I'll definitely check it out. I currently have my pinion at 5.5 degrees, right in between the trans angle 6.0 and the first shaft 5.0. It's the best I've ever got it, but I'm sure It can...
Showing results 1 to 50 of 229

 
Forum Jump

All times are GMT -4. The time now is 01:02 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.