home register FAQ memberlist calendar

Go Back   Turbobricks Forums > Search Forums

Showing results 1 to 17 of 17
Search took 0.00 seconds.
Search: Posts Made By: mike66
Forum: maintenance & nonperformance 07-13-2022, 12:53 AM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
yes, I realized I said that after I hit the...

yes, I realized I said that after I hit the button. It was driving on jack stands at 45-50 mph. with zero pressure. I realize no pressure at "idle" my bad.
Forum: maintenance & nonperformance 07-12-2022, 07:46 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I've tried 3 solenoids, one that I know worked a...

I've tried 3 solenoids, one that I know worked a couple of moths ago on my P-type. How much of a voltage drop is too much at the solenoid? My battery reads 12.18 (Low) Volts and I've got 10.6 at the...
Forum: maintenance & nonperformance 07-12-2022, 07:33 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
oops

oops
Forum: maintenance & nonperformance 07-12-2022, 03:40 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I Just tested it again with the same results....

I Just tested it again with the same results. Zero pressure running on jackstands up to 55mph. I cannot rule out the cheap gauge I bought from eBay but I did blow shop air into it and it read pretty...
Forum: maintenance & nonperformance 07-12-2022, 01:42 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I'm about to re-test the pressure today. last...

I'm about to re-test the pressure today. last test I had zero pressure all around. I did not rotate the crankshaft while it was apart I considered it but I was working alone and I don't have a remote...
Forum: maintenance & nonperformance 07-12-2022, 12:11 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I removed the OD pan and took out the center plug...

I removed the OD pan and took out the center plug under the pump and made sure the ball was seated properly and the spring seemed ok. Still no pressure at any speed and no OD still won't engage. any...
Forum: maintenance & nonperformance 07-07-2022, 04:59 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I Applied shop air to the gauge and it moved...

I Applied shop air to the gauge and it moved accordingly. So I’m guessing I have a pressure issue.
Forum: maintenance & nonperformance 07-06-2022, 01:17 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
well.... I bought a cheap pressure gauge off of...

well.... I bought a cheap pressure gauge off of ebay, made an adapter to fit and the result is: I have zero pressure at the port under any condition? Might be the cheap gauge? or a bad pump? Thoughts
Forum: maintenance & nonperformance 06-23-2022, 07:34 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
Also I doubt its an O- ring issue because I just...

Also I doubt its an O- ring issue because I just replaced them all.
Forum: maintenance & nonperformance 06-23-2022, 07:34 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
Couldn't i just check pressure running it on a...

Couldn't i just check pressure running it on a lift or jacks, with the engine? Also any suggestions on a affordable pressure gauge?
Forum: maintenance & nonperformance 06-23-2022, 02:54 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
Update: I swapped in a known good solenoid and...

Update: I swapped in a known good solenoid and still no OD. I've got good power and ground and could still hear the same sound from the other solenoid, I would say both that I tried are working. I...
Forum: maintenance & nonperformance 06-22-2022, 01:27 AM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
These were originally the big O-rings so I just...

These were originally the big O-rings so I just replaced them. It was from an 85' 740 and the gearbox is now a iron case from who knows what year 240. I did make sure the solenoid was free when I had...
Forum: maintenance & nonperformance 06-20-2022, 08:50 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I could check the amp draw but its clicking...

I could check the amp draw but its clicking pretty good, I also have all of the greenbooks for these models. I don't have a set up to check the pressure either. At this point I think its ether a...
Forum: maintenance & nonperformance 06-20-2022, 08:32 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
Tapping did nothing. I have 12.2 volts at the...

Tapping did nothing. I have 12.2 volts at the battery which is a little low form sitting. and I have 11.9 volts at the solenoid. So a slight voltage drop but that should be enough to engage the OD....
Forum: maintenance & nonperformance 06-20-2022, 06:35 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
I'll try the old starter tap method. Yes I used...

I'll try the old starter tap method. Yes I used basic Type F from car quest. I used the same ATF for assembly. I plan to maybe go synthetic after a few hundred miles. But honestly I've always used...
Forum: maintenance & nonperformance 06-20-2022, 05:14 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
Yes, replaced a P-type (loud but functional) with...

Yes, replaced a P-type (loud but functional) with a J type.

I meant that I verified that the 4th gear lockout and reverse switch were functional. After further diagnosis today I am leaning toward...
Forum: maintenance & nonperformance 06-20-2022, 01:04 PM
Replies: 32
740: OD issues
Views: 1,820
Posted By mike66
OD issues

I just put a low milage m46 gearbox with a J Type OD on my 89 745T. I disassembled the OD and replaced all of the seals. everything looked OK inside. Now after I got it installed the speedo is not...
Showing results 1 to 17 of 17

 
Forum Jump

All times are GMT -4. The time now is 01:54 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.