• Hello Guest, welcome to the initial stages of our new platform!
    You can find some additional information about where we are in the process of migrating the board and setting up our new software here

    Thank you for being a part of our community!

1995 850T5R (yellow)

Hank Scorpio

Chubfest 2009 Survivor
300+ Club
large.jpg


1995 Volvo 850T5R
Engine:
B5234FT
SPM Rods
Mahle OS2 pistons
RKautotechnik STG3 head (OEM Valve size, ported, polished, 3 angle valve job 44CFM improvement @ .300lift per intake port, 43CFM @ .300 lift per exhaust port)
S60R Exhaust manifold (35% gain in flow)
GT3071R 63AR 5bolt, small inlet compressor, ATP Ultimate Internal Gate
NA cams
960 65mm Throttle Body, Ported intake manifold
UR crank pulley, entire rotating assembly balanced to with in .1gram
Eurospec T5R Manual ECU (dialed for 550's and an approximation based on mods fuel map) + Civinco BC500 Piggyback tuning system
Precision Core custom built FMIC
S60R IC upper pipe, 2.5" Hard piping
Turbosmart Sleeper Series Megasonic Blow Off Valve
Quickbrick Motorsports (QBM) Delrin upper engine mount
QBM Polyurathane reinforced upper firewall mount
QBM Polyurathane reinforced lower torque mount
3" Downpipe, ATPturbo 3" Cat, 3" Dynamax Bullet Muffler (middle), 3" HKS Carbon/Ti muffler (rear)
Eurosport Tuning Intake (Heat Shield, larger K&N Cone filter used)
OEM wiring harness converted to MT config
Samco Cooling hoses
ATPturbo.com Silicone Vacuum lines
Gemini Composites Carbon Kevlar throttle and cam covers

The entire Motor build, 5spd swap ect blog

medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg
medium.jpg


Transmission
M56H 5 speed transmission (swapped from the OEM automatic)
850R clutch

Suspension/Brakes:
RKautotechnik/Kaphlenke Adjustable Lower Control Arms
RKautotechnik/Kaphlenke Coil Overs
- Custom developed Koni inserts (front) single adjustable
- 450# front springs
- Koni adjustable rear shocks
- 375# rear springs, custom adjustable perches
RKautotechnik/Kaphlenke Camber Plates
Quick Brick Motorsports Sway Bar End Links
Stoptech ST40 BBK 332x32MM 2pc discs (front)
S60R 4piston Brembo Rear calipers, 330x28mm rear discs
Braided SS lines
Dot4 Motul fluid
Volvo Pegasus 18x8 Wheels (ET42)
Falken Azenis RT615 225/40/18
medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg
medium.jpg


Stereo:
Kenwood Headunit
Delphi Roady2 XM unit
iPod
JL Audio 12W3V2
JL Audio 250/1
JL audio 5.25 (front doors)
JL Audio 350/1
Morel Componets (rear shelf and front dash)
Infinity Reference 5.25 (rear doors)
Strike 1f capacitor
medium.jpg
medium.jpg



Interior:
Yazaki Gauge Cluster, QBM trim rings
EST Short Shifter
Momo Combat EVO Shift Knob
Momo Suede Shift Boot
Lotek 3 pillar gauge pod
Autometer Boost, Oil Temp, Oil Pressure gauges
Innovate Motorsports XD1 (Stand Alone Gauge kit-Wideband)
Factory T5R Suede trim package
medium.jpg
medium.jpg

(old pictures)

Exterior:
Gemini Composites CF/Kevlar piece between the tails
iPd mesh grille
5%tint
Saab lip spoiler
ExExPat'erized Projectors
medium.jpg
medium.jpg



Projects Im working on:
Over the last two months I've been building, collecting parts and doing a few things.

medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg
medium.jpg

medium.jpg


Dyno
Heres the thread: http://www.forums.turbobricks.com/showthread.php?t=75131
63083440.jpg

63083442.jpg


finally a couple nice pictures
medium.jpg
medium.jpg

72130539.jpg

72130470.jpg

64885846.jpg

64885853.jpg


For more pictures: http://www.pbase.com/dkauer744/1995_volvo_850_t5r

Videos
<object width="425" height="350"><param name="movie" value="http://www.youtube.com/v/LGcB3Fj-tIQ"></param><param name="wmode" value="transparent"></param><embed src="http://www.youtube.com/v/LGcB3Fj-tIQ" type="application/x-shockwave-flash" wmode="transparent" width="425" height="350"></embed></object>

<object width="425" height="350"><param name="movie" value="http://www.youtube.com/v/Rvv88q4GyhY"></param><param name="wmode" value="transparent"></param><embed src="http://www.youtube.com/v/Rvv88q4GyhY" type="application/x-shockwave-flash" wmode="transparent" width="425" height="350"></embed></object>
 
Last edited:
That's worth about as much hp as a ricer sticker. Looking good Doug. I'd put up a project thread for my 744, but it'd just say "pending" for like 17 years....
 
I dont know why you torture me.




man, im really getting annoyed driving around a beatup 242..class and leather T5-R make more sense, and with those mods, corvettes are pish posh..

I still dont see how you can grow out of a done up 242..another enigma of Doug.
 
Last edited:
isaac said:
You should list "has been driven by Isaac" as a mod.
or is that "survived being driven by Isaac" :-P :-P

really good job on the boot install doug - shows me how mine SHOULD look!! :lol:
 
Nice smile. You should paint over the Porsche logo on the front calipers. Just doesn't seem right haha. I'm interested in those CRX projectors. How did you do that?
 
What's wrong with that? I wouldn't want it to say Porsche on my Volvo, even if the calipers did come from a nice porsche and they are better brakes.
 
Snoop Dougy Doug said:
I guess thats the difference between you and I. :rofl:

D00d, paint them grey like the rear calipers. Keep the Porsche logo...I HATE red calipers.

But it's your car. ;-)
 
Snoop Dougy Doug said:
:rofl: :rofl: It IS my car ;-) I do like the hyundai idea though :rofl:

btw, did a new gauge cluster setup today :-D
[ img]http://www.pbase.com/dkauer744/image/52469647.jpg[/img]

Eh? Wass tat? V70 cluster? No turbo gauge?
 
Back
Top