Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Pulled the stock wiring out last night, 12 pounds,
Last edited:
-
Hello Guest, welcome to the initial stages of our new platform!
You can find some additional information about where we are in the process of migrating the board and setting up our new software hereThank you for being a part of our community!
Muellers '78 242 project, warning, it's ugly right now :)
- Thread starter Mueller
- Start date
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Engine getting a little more bare..
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Pulled the dash, w/pad and gauges it weighs 17 pounds
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Going shopping for an a/c setup soon. The vents and tubes for the heat and ventilation are full of dirt and dust...need a good cleaning
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
................
Last edited:
Mylesofsmyles
A Member
- Joined
- Jan 18, 2010
I hope something fun and aspirated is going in there.
Lord_Athlon
300+ Clurb
- Joined
- May 20, 2003
- Location
- Eau Claire, WI.
I hope something fun and aspirated is going in there.
Most engines aspirate
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
I hope something fun and aspirated is going in there.
Stockish B230F for now.... have something fun and different planned, no pictures until it is developed a little more to make sure it works okay.... it'll get laughed at if talked about without proof of concept
Mylesofsmyles
A Member
- Joined
- Jan 18, 2010
No, you'll just get laughed at for taking FOREVER!!!!!!!!!!!!!
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Crazychopstick
(/// _ - )
- Joined
- Dec 22, 2004
Yay progress!
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
yep !!
even removed the front fenders yesterday once I got over my depression of all the bondo in the engine compartment
Crazychopstick
(/// _ - )
- Joined
- Dec 22, 2004
yep !!
even removed the front fenders yesterday once I got over my depression of all the bondo in the engine compartment
You know what's the best cure for depression over Bondo in the engine compartment?
Pegs.
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Couldn't go outside and play in the garage tonight so I sat in front of the computer to learn a new software package I've had for a while....
This is the rear frame rail, not going to be 100% exact with the tracing method, but it'll be close enough once I grab some numbers off the car and adjust the model.
This is the rear frame rail, not going to be 100% exact with the tracing method, but it'll be close enough once I grab some numbers off the car and adjust the model.
Attachments
Mylesofsmyles
A Member
- Joined
- Jan 18, 2010
^ Looks scientific!
Is this car ever going to run?
Is this car ever going to run?
Mylesofsmyles
A Member
- Joined
- Jan 18, 2010
^ Looks scientific!
Is this car ever going to run?
Is this car ever going to run?
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
D.E
tvåförti
- Joined
- Sep 15, 2010
- Location
- Mora, Sweden
IRS in a 240? Winning.
Mueller
Active member
- Joined
- Oct 12, 2004
- Location
- Antioch, CA
Started on the power steering rack rebuild, (new seals and bushings)
Kit was a little over $100...
So far I have been able to make my own special tools, nothing too fancy.
I need to modify the tool for the collars so that I can use my torque wrench when I put it all back together.
Last pic is the tool on my mill, next version will be nicer
Kit was a little over $100...
So far I have been able to make my own special tools, nothing too fancy.
I need to modify the tool for the collars so that I can use my torque wrench when I put it all back together.
Last pic is the tool on my mill, next version will be nicer
Last edited: