home register FAQ memberlist calendar

Go Back   Turbobricks Forums > General > article composition

Reply
 
Thread Tools Display Modes
Old 01-11-2013, 01:06 PM   #26
naza
Newbie
 
Join Date: Mar 2012
Location: malaysia , selangor , sekincan , pasir panjang
Default EZ116K daughterboard assembly kit

how price EZ116K daughterboard assembly kit? and shipping malaysia? please pm .
naza is offline   Reply With Quote
Old 12-30-2013, 05:12 PM   #27
REDBLOCK
Board Member
 
REDBLOCK's Avatar
 
Join Date: Jan 2009
Location: Lublin/Poland
Default

these kits dont work with chips!
REDBLOCK is offline   Reply With Quote
Old 05-03-2014, 01:34 PM   #28
surbotaab
Newbie
 
Join Date: May 2014
Default

Hi, does blabla still supply these? I`ve tried to send a PM but getting a error saying his inbox is full...
surbotaab is offline   Reply With Quote
Old 10-01-2020, 12:39 PM   #29
dalek
Benchracer Tribe
 
dalek's Avatar
 
Join Date: Oct 2005
Location: Orange Alert, NC
Default

Quote:
Originally Posted by surbotaab View Post
Hi, does blabla still supply these? I`ve tried to send a PM but getting a error saying his inbox is full...
Arise from the dead!
(Well, it might be useful to someone)

https://www.classicswede.co.uk/EZK_D..._17042139.aspx
http://bijlsmatechnicalinnovations.n...hterboard.html
__________________
"you can't leave your thingy hanging in public... you can get arrested."
"What's Arkansas supposed to be, Kansas for pirates?" Forg
"I think I can touch the tire. Damn! I can touch the tire! That hurts!" 240Psycho (on the back seat of my 94 Jetta while I was driving to a J/Y)
"Use the barbed adapter like what I use to inflate the air camping mattresses and my dates." FTF Engineering
i am inspired. i will replace my windsheild... with an intercooler.swedishK
Feedback!
dalek is offline   Reply With Quote
Old 10-07-2020, 04:08 AM   #30
deNs
Newbie
 
deNs's Avatar
 
Join Date: Aug 2015
Location: Australia
Default

Edit: didn't realise the post you were responding to was so old!

He was responsive to me on bijlsmatechnicalinnovations@gmail.com. I recently purchased chips and a daughterboard kit from him. The email exchange sometimes had delays of a few days, but if you're patient it's all good. Everything arrived well packed.
deNs is offline   Reply With Quote
Old 12-05-2020, 05:58 PM   #31
carver
Involvoed
 
carver's Avatar
 
Join Date: Apr 2011
Location: Seattle
Default

As long as it's resurfaced... Do yourself a favor and ditch the crappy sockets included with this kit. I replaced mine with the following from Phoenix Enterprises:

HWS9037 28 pin DIP IC Socket Machined .6"
HWS3937 20 pin DIP IC Socket Machined .3"
carver is offline   Reply With Quote
Old 01-21-2021, 09:27 PM   #32
deNs
Newbie
 
deNs's Avatar
 
Join Date: Aug 2015
Location: Australia
Default

I've finally got around to assembling the daughterboard and have finally got a multimeter with me to check something that was noted in the assembly guide, as per this thread.





It points out specifically that last pin on the 20-pin header to make sure it's not connected to where one of capacitors is, which is very close on the PCB. I was careful to solder it, however it appears to have continuity anyway. I noticed this post earlier in the thread that suggests that perhaps it is supposed to be connected and can work fine:

Quote:
Originally Posted by Garfield View Post
And there it was: a bad connection on one of the capacitors. This pin is very close another one and I had been to careful not to connect them to each other. Now I noticed the board connected them anyway, so being careful wasn't necessary. Just to be safe I re-soldered a couple of other connections too, although they seemed fine, and then I tried again. I have never been so relieved that my car didn't start.
Then I changed the jumper to position 1-2, and it started up fine.
Though it's confusing that the guide specifically states that you should make sure that the points aren't connected. I figure that a guide from the people who are getting PCBs made up should have reliable information, but it seems to conflict.



Is anyone able to confirm if the traces on the bare board are supposed to have continuity? The photo above is how my board currently is, which has continuity between those two points, after using a solder wick to remove as much solder as possible while still maintaining a reasonable connection.
deNs is offline   Reply With Quote
Old 01-21-2021, 09:40 PM   #33
bobxyz
Board Member
 
bobxyz's Avatar
 
Join Date: Aug 2014
Location: Boulder CO
Default

That's funny. I just looked at my unassembled board and there's a big fat trace connecting those 2 holes on the other side of the board. So, the instructions are confused and yes, there should be continuity. You can see it in the corner of this picture (ignore the line between the holes, it's just silkscreen/soldermask on top of the trace).

__________________
'85 245glt b21ft aw71 k-jet -> lh2.4

Last edited by bobxyz; 01-21-2021 at 10:03 PM.. Reason: added pic
bobxyz is offline   Reply With Quote
Old 01-21-2021, 09:46 PM   #34
deNs
Newbie
 
deNs's Avatar
 
Join Date: Aug 2015
Location: Australia
Default

Quote:
Originally Posted by bobxyz View Post
That's funny. I just looked at my unassembled board and there's a big fat trace connecting those 2 holes on the other side of the board. So, the instructions are confused and yes, there should be continuity.
I thought I was going nuts. Thanks for confirming it so quickly. Now I can solder it into my EZK with peace of mind! :D
deNs is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 03:08 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.